利用ps2键盘向单片机输入数据，这样做不仅可以减少输入输出口，而且程序代码短小精悍，可以极大的提高单片机的执行效率．...

AVR单片机开发EEPROM读写实验源程序-AVR single-chip EEPROM read and write to develop the experimental source

KS0108控制器的12864液晶驱动，实现图片和中文全角，英文半角显示-12864 controller KS0108 LCD driver, realize the whole picture and the Chinese angle, the English half-angle display

设计的主要内容如下 （1）设计一款电子秤，用LED液晶显示器显示被称物体的质量 （2）可以设定该秤所称的上限 （3）当物体超重时，能自动报警 （4）写出详细的实验报告 -The design of the main contents are as follows (1) the design of an electronic scale, liquid crystal display with LED shows that the quality of objects (2) can set the scale referred to as the upper limit (3) When the objects are overweight, they can auto-alarm (4) write a detailed experimental report

基于AT89C2051的照明系统控制程序，实现照明设备的自动控制。-AT89C2051-based lighting systems control procedures, to achieve automatic control of lighting equipment.

这是AD转换芯片AD7705的初始化程序，主要是寄存器的配置-This is the AD conversion chip AD7705 initialization procedure is the configuration register

用凌阳单片机输入频率控制并输出14位2进制码锁住相应频率-With Sunplus Singlechip frequency control input and output 14 2 hexadecimal code corresponding frequency locked

应用于ARM单片机的LCD1602的驱动代码-Applies to ARM MCU LCD1602 driver code

周立功单片机ARM学习板easyARM2104的测试程序等-weeks learning meritorious ARM MCU board easyARM2104 testing procedures

收集到的一些常用功能模块，有温度传感、星期计算、一按键都能等-Collected some frequently used function modules have temperature sensing, weeks, and so one button can

单片机RS232/RS485串行发送实验（双机通讯）。 实验步骤： （1），准备两台598K实验机，确定1号机为发送，2号机为接收； （2），当作RS232接口实验时，1号机和2号机的P3.0和P3.1交叉相连，且两机共地； （3），当作RS485接口实验时，1号机和2号机的A、B作对应连接，同时1,2号机的R/TEN接P1.0, P3.0接R0, P3.1接DI。 （4），先运行2号机，键入[27]-->[EV]使2号机处于接收状态P。，后运行1号机[26]-->[EV]使1号机处于发送状态,P。会闪烁，在1号机键盘上按动数字键，在2号机的数码管上应显示对应的数字键值。-Send Singlechip RS232/RS485 serial experiment (two-plane communications). Experimental steps: (1), prepare two sets of experiments 598K machine, determined on the 1st machine to send, on the 2nd machine to receive (2), as a RS232 interface experiment, on the 1st and the 2nd machine and P3.0 P3.1 cross-linked, and the two planes were to (3), as a RS485 interface experiment, on the 1st and the 2nd machine A, B for the corresponding connection, while 1,2 No. of R/TEN then P1 .0, P3.0 access R0, P3.1 then DI. (4), first run on the 2nd machine, type [27]