登录
首页 » SCM » This is the AD conversion chip AD7705 initialization procedure is the configurat...

This is the AD conversion chip AD7705 initialization procedure is the configurat...

于 2022-08-18 发布 文件大小:718.00 B
0 152
下载积分: 2 下载次数: 1

代码说明:

这是AD转换芯片AD7705的初始化程序,主要是寄存器的配置-This is the AD conversion chip AD7705 initialization procedure is the configuration register

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 程序采用枚举法,顺序获取u
    程序采用枚举法,顺序获取u-disk设备描述符(包括vid、pid...)-Procedures using enumeration method, the order to obtain u-disk device descriptor (including vid, pid ...)
    2022-01-25 15:58:50下载
    积分:1
  • 是一个很好的描述单
    是一款不错的单片机开发软件说明,开发单片机前的必备知识学习。-Is a good description of single-chip microcomputer software, the development of single-chip pre-requisite knowledge.
    2022-03-10 04:23:41下载
    积分:1
  • 三相步进电机的三相六拍工作方式,正转的绕组通电顺序:A、AB、B、BC、C、CA、A,反转的通电顺序:A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性,故步进电机的工作过程中不能及时的启动和停止,在启动时应慢慢的加速到预定速度,在停止前应逐渐减速到停止,否则,将产生失步现象。 步进电机的控制问题可总结为两点: 1、产生工作方式需要的时序脉冲; 2、控制步进电机的速度,使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.
    2022-07-20 15:21:46下载
    积分:1
  • development compilation of telephone fees, as SCM lovers can learn to practice e...
    汇编开发的电话收费表,可以作为单片机爱好者学习练习的例子-development compilation of telephone fees, as SCM lovers can learn to practice examples
    2022-04-08 13:38:01下载
    积分:1
  • 本程序是一个ZLG7290的驱动程序。要用的朋友来下载吧...
    本程序是一个ZLG7290的驱动程序。要用的朋友来下载吧-This procedure is a ZLG7290 drivers. To use a friend to download it
    2022-02-26 17:09:56下载
    积分:1
  • 基于AVR单片机ATmega32 DS1820的驱动程序
    基于AVR ATmega32 单片机的DS1820驱动程序 基于winavr 平台编译 -ATmega32 based AVR MCU DS1820 driver-based winavr Taiwan compiler
    2022-06-15 14:18:10下载
    积分:1
  • 我上传的是单
    本人上传的是 单片机 蜂鸣器奏乐(生日快乐).asm 源代码 -I uploaded is the single-chip buzzer music (happy birthday). Asm source code
    2022-05-17 00:18:48下载
    积分:1
  • 程序详细功能介绍: * 利用AT89S51单片机的P0端口的P0.0-P0.7连接到一个共阳数码管的a-h的笔段上, * 数码管的公共端通过三极管8...
    程序详细功能介绍: * 利用AT89S51单片机的P0端口的P0.0-P0.7连接到一个共阳数码管的a-h的笔段上, * 数码管的公共端通过三极管8550选通。在数码管上循环显示0-9数字,显示时间的间隔可通过修改延时程序。 -Procedures detailed functional Introduction:* use AT89S51 MCU port P0 is connected to P0.0-P0.7 Yang a total digital control of the a-h T segment,* digital tube through the public side-gated transistor 8550. In the digital control on the circulation figures 0-9 show, indicating the time interval may be delayed by modifying the procedures.
    2022-02-11 11:06:45下载
    积分:1
  • Verilog realize the DDS sine wave signal generator and frequency measurement mod...
    Verilog实现的DDS正弦信号发生器和测频测相模块,DDS模块可产生两路频率和相位差均可预置调整的值正弦波,频率范围为20Hz-5MHz,相位范围为0°-359°,测量的数据通过引脚传输给单片机,单片机进行计算和显示。-Verilog realize the DDS sine wave signal generator and frequency measurement module test phase, DDS module can generate both frequency and phase difference can be preset to adjust the value of sine wave, frequency range of 20Hz-5MHz, phase range of 0 °-359 ° , measurement data and transmit them to the single-chip pin, single-chip microcomputer to calculate and display.
    2022-04-02 09:35:43下载
    积分:1
  • avr 单片机LED驱动程序源代码c程序设计
    avr 单片机LED驱动程序源代码c程序设计-Single-chip LED driver avr source code c programming
    2022-07-13 14:11:17下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载