PIC单片机控制12位高速串行DA（max538）产生阶梯波

微软的usb网卡(RNDIS)的相关协议以及驱动程序。-Microsoft usb adapter (RNDIS) the relevant agreements, as well as drivers.

R2S15902音频IC I2C初始化 用于音响、车载等 -IC I2C initialization R2S15902 audio for audio, car, etc.

串行存储器拷贝器-copy serial memory device

单片机实现语音控制小车电路原理图和1个设计的文档说明,相信对想做语音控制的朋友很有帮助-MCU voice control car circuit schematics and a design document that voice wants to believe that the right to control the helpful friends

本程序为完成各种中断的演示.at91sam7s64芯片,ads1.2编译器.代码说明： 1)完成基本的初始化 2)初始化PIO,IRQ,FIQ,software_interrupt等 3)驱动板上的四个按键(PB1,PB2,PB3,PB4) 4)初始化DEBUG口，Usart1等 5)初始化定时器timer0,timer1等-procedures for the completion of the various demonstration interrupted. At91sam7s64 chips ads1.2 compiler. source : 1) completion of the basic initialization 2) initialization PIO, IRQ, FIQ, software_interrupt three) driver board the four buttons (PB1. PB2, PB3, PB4) 4) initialization DEBUG mouth, Usart1 five) initialize the timer timer0, timer1 etc.

在QuartusII中使用AHDL语言编写一个RS232串行数据通信接口，要求设计输入输出端口，要求能提供的接收端口正确地接收。其中1bit作为start位，8bit作为数据，1bit作为end位。-QuartusII used in the preparation of an AHDL language RS232 serial data communication interface to design input and output ports, require the receiver to provide the correct port to receive. 1bit as one start bit, 8bit as data, 1bit as the end bit.

请在本目录存放UCOS 2.52源代码，包括OS_CORE.C、OS_FLAG.C、OS_MBOX.C、OS_MEM.C、OS_MUTEX.C、OS_Q.C、OS_SEM.C、OS_TASK.C、OS_TIME.C和uCOS_II.H。 -Stored in the catalog UCOS 2.52 source code, including OS_CORE.C, OS_FLAG.C, OS_MBOX.C, OS_MEM.C, OS_MUTEX.C, OS_Q.C, OS_SEM.C, OS_TASK.C, OS_TIME.C and uCOS_II.H .

AVR music player.. CVAVR source code included v2...cool:)

2410addr.inc：s3c2410内部寄存器定义 memcfg.inc : 存储块配置，主要定义时序 option.inc : s3c2410堆栈地址，时钟等设置 。 2410init.asm: 启动代码 -2410addr.inc : s3c2410 internal registers definition memcfg.inc : storage block allocation Timing option.inc main definitions : s3c2410 stack addresses, putting the clock. 2410init.asm : bootcode

应用背景STM32可以用来接入SD卡和SPI FLASH芯片，USB Mass Storage类支持两个传输协议： 1）Bulk-Only 传输（BOT） 2）Control/Bulk/Interrupt传输（CBI） USB  驱动 关键技术开机的时候先检测SD卡和SPI FLASH是否存在，如果存在则获取其容量，并显示在LCD上面（如果不存在，则报错）。之后开始USB配置，在配置成功之后就可以在电脑上发现两个可移动磁盘。驱动USB从而读取。