基于凌阳单片机的语音 手动 播放音乐 的 汇编程序

IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta

基于AT89C2051的照明系统控制程序，实现照明设备的自动控制。-AT89C2051-based lighting systems control procedures, to achieve automatic control of lighting equipment.

一个执行效率不错的键盘扫描程序。附有Proteus仿真，按键的键值通过ＬＥＤ显示-A good efficiency in the implementation of the keyboard scanner. With Proteus simulation, the key button LED display through

51单片机c语言教程，包含寄存器设置和部分实例，不错的入门教程。-51 single-chip c language tutorial, including part of examples and register settings and , a good introductory tutorial.

keil下驱动程序的编写，VC-the driver prepared, VC

c8051f340 USB传输 固件驱动， c8051f340 USB传输 固件驱动，-c8051f340 USB transfer firmware drivers, c8051f340 USB transfer firmware driver

本方案适用于研究生、本科、大专、职业技术学院的嵌入式系统（单片机/ARM7） 应用、信息通信、应用电子、机电一体化、微机应用、数控技术、自动化控制、计 算机原理与应用、仪表及控制、汽车工程等与“电子/微机/总线”有紧密联系的相关 专业。-The program applies to postgraduate, undergraduate and post-secondary schools, vocational and technical colleges Embedded System (SCM/ARM7) applications, information communications, electronic, electromechanical integration, application of computer, NC technology, automatic control, computer science and application, Instrumentation and Control , automotive engineering, and "electronic/computer/bus" is closely linked to the relevant professional.

MSP430串口程序，串口接收与发送均用中断处理。当MSP430串口中断接收到PC机的指令后通过中断发送将数据发送出去。-MSP430 serial program, serial port receive and send all use interrupt handling. When the MSP430 serial receive interrupt instruction PC, adopted after the break to send the data sent.

LCD DS1302,MEGA16，显示一个万年历，用ICCAVR编译器编写-LCD1302, MEGA16, display a calendar with the preparation of the compiler ICCAVR

一个时时单片机发送数据测试代码-a microcontroller always send data test code