单片机C语言的精确延时程序设计，很有用的哦

用EPM1270实现的1602液晶驱动Verilog-EPM1270 achieved by 1602 LCD driver Verilog

CDLEA.hex CDLEA_Main.c CDLEA.hex为已编译的红外遥控音源切换器的单片机程序 CDLEA_Main.c为源代码 CDLEB.hex CDLEB_Main.c CDLEB.hex为已编译的加强版的红外遥控音源切换器的单片机程序 　　有红外遥控PC功能,PC软件可使用Grider3.2(SAA3010T电视遥控器) 　　Grider3.2可到http://cdle.yeah.net下载 CDLE_A410.exe 为红外遥控音源切换器的ＰＣ应用软件。-CDLEA.hex CDLEA_Main.c CDLEA.hex compiled for the red outside sources of remote switching of SCM CDLEA_Main.c procedures for the C source code CDLEB.hex DLEB_Main.c CDLEB.hex compiled for the enhanced version of the infrared remote control sources of the single switches machine procedures with infrared remote control PC functions, PC software can be used Grider3.2 (SAA3010T TV remote control) Grider3 .2 can http :// cdle.yeah.net download CDLE_A410.exe sources of infrared remote control switches the PC application software.

mcs-51单片机实用子程序库-mcs-51 microcontroller practical subroutine library

实现STC89LE516AD单片机的A/D转换功能，时钟11.0592M，转换结果以16进制输出到串行口，可用串行口调试程序并观察输出结果，注解非常详细。-Achieve STC89LE516AD MCU A/D conversion clock 11.0592M, conversion results to 16 hexadecimal output to the serial port, serial port can be used to debug programs and observe the output, very detailed comments.

用反转法实现快速高效的4*4键盘扫描，并通过串口将按键值输出-Inversion method with fast and efficient implementation of the 4* 4 keyboard scanning, and send out the key value through the serial port

这是一个51单片机与PC的通信系统：利用3*4小键盘输入0~9的一串数字（不大于5），通过8051自带的串口发送给PC并显示在系统的6位LED上；单片机接收上位机的输入并显示在LED上。8051串行口经232电平转换后，与PC机串行口相连。PC机使用串口调试应用程序V2.2.exe，实现上位机与下位机的通讯。-This is a 51 microcontroller and PC communication system : use 3* 4 0 small keyboard input of a bunch of nine-figure (no more than 5), by 8051, bringing their serial sent to the PC and display system in the six LED; SCM receiving PC input and displayed on the LED on. 8,051 by 232 serial port-level conversion, and the PC serial port connected. PC using serial debugging applications V2.2.exe achieve PC and the next crew communications.

在keil-ARM环境下对ARM7处理器编译成功的I2C总线程序，程序通过I2C总线向UART串口发送数据，验证了I2C总线程序的正确性。-Keil-ARM in the circumstances of the ARM7 processor to compile the success of I2C bus procedures, procedures for the adoption of I2C serial bus to send data to the UART, I2C bus to verify the correctness of the procedure.

本设计提供了通过单片机来控制温度测量芯片18b20，进行测量温度-This design through the single-chip microcomputer to control the chip temperature measurements 18b20, measured temperature

一个完整的STC89LE5412程序，实现２路电压，２路电流采样，滤波，和瞬间功率峰值计算-A complete STC89LE5412 procedures, to achieve 2-way voltage, 2-way current sampling, filtering, and calculation of instantaneous peak power

次文件包括uCOS-II中使用,ZLG_FS在CF卡上的例子,ARM采用的是LPC2210.-Meeting documents include uCOS-II use, ZLG_FS in the CF card example, ARM using the LPC2210.