相关富士通单片机实用资料

红外接收C库文件, 晶振:11.0592,中断方式-Infrared receiver C library file, crystal: 11.0592, interruption mode

Split Plane samples for stb s asm driver-Split Plane samples for STB s asm driver

1602LCD 的介绍以及汇编程序，比较详细，内有现成模块，可直接调用-1602LCD the introduction as well as the compilation process in more detail, which has off-the-shelf modules, can be directly called

三菱梯形图转成51单片机HEX文件。 三菱软件写好梯形图，再运行转换软件，设定好51单片机的输入输出， 打开写好的梯形图，转换出的就是hex文件，烧录到51单片机，51单片机 就可以执行PLC的动作了。51单片机控制板价格便宜，可以代替简单场 合的PLC，控制成本降低。 1：把PWM转换后，在PWM文件下生成一个HEX文件。 2：生成的文件很大，51单片机要选用8K以上(AT89S52就是8K)储存量的。 3：把HEX文件下载到单片机就可以用了。 -Mitsubishi ladder into 51 single-chip HEX file. Mitsubishi software written ladder, and then run the conversion software, set 51 single-chip input and output, open ladder-written, conversion is a hex file, burn to 51 single-chip, 51 single-chip microcomputer can be implementation of the action of PLC. 51 Single-chip panel prices, can replace the simple occasions PLC, control and lower the cost. 1: after the PWM converter, PWM documents generated in a HEX file. 2: generate a lot of paper, 51 single-chip 8K to choose more than (AT89S52 is 8K) storage capacity. 3: The HEX file can be downloaded to a single-chip microcomputer used.

设计使得原本需要14个IO接口的键盘显示少用了9个单片机IO接口,虽然该设计的优势在本实验中没有完全体现出来,但若在现代工业设计中应用此方案,在对引脚需要较大的产品中其优点将体现得淋漓尽致。.-Design makes the original needs 14 IO interface shows the use of a keyboard 9 Singlechip IO interface, although the advantages of the design in this experiment did not fully reflected, but in modern industrial design in the application of this program in the pairs of primers Products feet larger in its merits and will be reflected most vividly. .

一个用keil 51c实现的单片机系统程序，实现led显示和其他一些模块的控制-Using keil 51c realize a single-chip microcomputer system of procedures, led display and realize a number of other control modules

用中断的方式控制lcd的显示，单片机仍然是h83664十六位单片机。此程序包含单片机的接口的配置以及各种写lcd的子程，使用中断来控制lcd顺序显示A－Z，当然，可以换成其他的显示内容，由于接口程序已经编好，只需要把要显示的内容改一下就可以实现其他内容的显示-With interruption control lcd display, single-chip is still 16 Singlechip h83664. This procedure includes the configuration of single-chip interface and a variety of writing a sub-lcd-way, the use of interrupt to control the order in lcd display A-Z, of course, can be replaced by other display content, as a result of interface procedures have been developed only to To display the contents of change can be achieved about the display of other content

超声波测距,包括有pcb原理图，用c写的程序，还有详细的说明-Ultrasonic ranging, including schematics pcb with c written procedures, detailed instructions have

stc单片机IAP源码,可将数据写入单片机内部FLASH中,无须外扩FLASH,速度快-stc IAP source SCM, data can be written into the internal FLASH MCU, FLASH without foreign expansion, speed

PIC C18 读写TLC5628数字电位器程序-PIC C18 Digital Potentiometers TLC5628 to read and write procedures