USB转串口程序，已经调试通过，调试环境为keilc.

完整的LM240128的显示程序,可以通过修改程序中的变量来改变显示内容,P89C668环境,其他51内核单片机均可移植,也可以加入控制程序在不同的情况下显示不同的内容.经过调试可用.-LM240128 integrity of the display program, may amend the procedures to change the variable content, P89C668 environment, MCU 51 other kernel can be transplanted, can also include control procedures in different circumstances show different content. After debugging available.

基于凌阳61和pwm电机实现的智能车总程序，包含所有程序。-Sunplus based pwm motor 61 and realize the overall process of intelligent vehicles, including all the procedures.

51单片机控制TC35I无线通信模块的完整Keil C程序，还包含GB2312与Unicode转换，国标汉字、ASC字符显示，串口通信，液晶模块控制等程序。-51 single-chip wireless communication module TC35i control the integrity of Keil C procedures, also includes GB2312 and Unicode conversion, GB characters, ASC characters display, serial communications, LCD module control procedures.

51单片机控制的LCD1602读写控制程序LCD1602.c-51 single-chip control LCD1602 read and write control procedures LCD1602.c

ADI公司ADuC841单片机源程序。 I2C.c: ADuC841单片机I2C接口函数。 kei841.h： ADuC841单片机内部寄存器定义。 delay.c：精确延时资函数。 main_new.c ADuC841单片机主函数，实现正弦波的输出和I2C接口LED显示-ADI ADuC841 MCU source. I2C.c : ADuC841 MCU I2C interface function. Kei841.h : ADuC841 MCU internal register definitions. Delay.c : precision-delay function. Main_new.c ADuC841 MCU main function, achieve sine wave output interface and I2C LED Display

基于单片机的，ds18b20调试程序。注释清楚。可移植性好。-Based on SCM, ds18b20 debugger. Notes clearly. Good portability.

51单片机实现的温度测量、AD转换，温度传感器采用DS18B20，显示采用1602LCD屏，报警采用蜂鸣器。-。-51 MCU temperature measurement, police procedures, the use of temperature sensor DS18B20, showed that the use of 1602LCD screen, using buzzer alarm.

在MAGE128下使用240*128液晶实例-MAGE128 use in 240* 128 LCD example

MC9S12DG128B，包含了时间中断、光电检测、舵机控制、电机驱动、实时控制等功能。有相关注释。-MC9S12DG128B, includes a time interrupted, photoelectric detection, steering control, motor-driven, real-time control functions. Relevant Notes.

请将下载的2个插件内容拷贝到uVision 的安装目录下的 KeilC51BIN 中 2. 修改 Tool.ini, 此文件位于 uVision 的安装目录 keil 下. 请将下面的内容 添加到 [C51] 部分的后面. AGSI1=ledkey.dll ("ledkey") AGSI2=simboard.dll ("simboard") 3. 重启uVsion. 进入Debug 模式, 打开菜单Peripheral, 发现增加了2项 分别是键盘LED仿真板，51实验仿真板。-Please download the contents of two plug-ins are copied to the installation directory uVision under KeilC51BIN 2. Modify Tool.ini, this file is located in the installation directory uVision under keil. Please Add the following line to [C51] part of the back. AGSI1 = ledkey.dll (ledkey) AGSI2 = simboard.dll (simboard) 3. Reset uVsion. entered the Debug mode, open the menu Peripheral, found an increase of 2 are keyboard LED emulation board, emulation board 51 experiments.