AVR图形信号发生器

用8051单片机可实现音乐播放功能（以"新年好"为例）。如果安装了Proteus软件，可方便的在自己的电脑上实现仿真。-YOU KAN PLAY BEAUTIFUL MUSIC WITH THE HELP OF 8051MCU.YOU CAN SIMPLY MAKE IT IF YOU HAVE THE MASTERY OF PROTEUS.

单片机系统用c语言编写关于两个PIC之间的通信的设计。。。本程序采用的单片机型号为PIC16F8- Single-SCM systems c language on the communication between two PIC design. . . This procedure used for the PIC16F877 microcontroller model

rp89comdd mcs51单片机源码一堆-rp89comdd mcs51 SCM source heap

电子秒表的设计 1、用系统8253定时器提供的55ms定时单位，设计秒表定时程序。 2、有关系统定时方法： PC机系统中的8253定时器0工作于方式3，外部提供一个时钟作为CLK信号, 频率：f=1.1931816MHz。 定时器0输出方波的频率:fout=1.1931816/65536=18.2Hz。 输出方波的周期Tout=1/18.2=54.945ms。8253A每隔55ms引起一次中断-Electronic stopwatch design one, using the system timer 8253 provides 55ms timing units, design stopwatch timing procedures. 2, the system timing method: PC system timer 0 of 8253 working in the way of 3, to provide an external clock as the CLK signal, the frequency: f = 1.1931816MHz. Timer 0 output square wave frequency: fout = 1.1931816/65536 = 18.2Hz. Cycle square wave output Tout = 1/18.2 = 54.945ms. 8253A every 55ms caused a disruption

经典的DSP的C程序和汇编程序, 非常好!-Classic DSP-C procedures and compilation of procedures, very good!

单片机I2C协议代码， 单片机程序 c语言编写 -Single-chip I2C protocol code, single-chip microcomputer program written in c

HT1621 是一款128 个位元的LCD 控制器件，内部RAM 直接对应LCD 的显示单元。相应的软件使它适用于包括LCD 模块和显示子系统在内的多功能应用。主控制器与HT1621接口只需4 到5 根线。内置的省电模式极大的降低了功耗。本文介绍HT48R05A-1 单片机来控制HT1621，并介绍如何turn ON 及turn OFF LCD 所有位元。-HT1621 is a 128-bit LCD control device, the internal RAM directly correspond to the LCD display unit. So that it applies to the appropriate software, including LCD modules and display sub-systems, including multi-purpose applications. Master controller and the HT1621 interface only 4-5 lines. Built-in power-saving mode greatly reduce power consumption. This article describes the HT48R05A-1 microcomputer to control the HT1621, and describes how to turn ON and turn OFF LCD all the bits.

单片机串口通信的简单例程，供需要的人参考-A simple microcontroller serial communication routines for those who need it for reference

在单片机中，处理串口的子程序-in SCM, the serial processing subroutine

该程序提供步进马达的制造原理,控制原理.和C51控制标准程序,按此方法就可以作出!-the procedures for the motor manufacturing principles, the principle of control. C51 control standards and procedures, according to method can make!