读卡器SIM卡SIMcard读写模块源代码

很不错的频率计的设计，希望大家多多指教-Cymometer very good design, I hope everyone exhibitions

移动机器人摇杆手柄调速中(AD采集)，微控制器为MSP430，已成功调试用于机器人上！-Mobile Robot Control in the rocker lever (AD Acquisition), micro-controller for the MSP430, debugging has been successfully used on the robot!

CAN的调试程序。CAN的初始化重要包括下面几个方面。RXB0SIDH，RXB0SIDL，RXB0MIDH，RXB0MIDL。这是接收过滤器。TXB0SIDH，TXB0SIDL，TXB0DLC，这是发送标志位。还有波特率寄存器。操作模式为 正常模式。-CAN debugging procedures. CAN initialization important aspects include the following. RXB0SIDH, RXB0SIDL, RXB0MIDH, RXB0MIDL. This is the receiver filters. TXB0SIDH, TXB0SIDL, TXB0DLC, it is sending signs spaces. There baud rate register. The normal mode of operation for the model.

基于altera公司的cycloneIII_3c25_niosII的应用程序软件，是altera公司提供的标准例程，里面包含sd卡的读写，位图在lcd的显示等。-On altera" s cycloneIII_3c25_niosII application software, is provided by altera standard routines, which contains the sd card reader, lcd display bitmaps and so on.

对 CC2420 寄存器进行初始化，设置CC2420 寄存器数值，并读取设置的寄存器的数值。 本实验以CC2420 中的MDMCTRL0 为例，进行设置，并读取其设置的数值在串口工具上显 示出来。-Initialization of the CC2420 registers set CC2420 register values, and read the register set value. In this experiment, CC2420 in MDMCTRL0, for example, be set and read the value of its settings in the serial port tools displayed.

本程序功能是利用单片机控制用户板上的小键盘，将按下的键通过单片机的串口发送给PC机，在PC机串口助手显示出来。用行翻转法的方法来识别输入的键盘。 二、通过单片机将键盘按下的键在LCD上显示出来。 -This procedure is the use of single-chip control functions of the user on-board a small keyboard, the keys will be pressed through the single-chip serial port sent to the PC, the PC Serial Port assistants displayed. Line inversion method used to identify the method of keyboard input. Second, through the single-chip microcomputer keyboard keys pressed on the LCD display.

此程序为是用在电子警察上面的，模拟 红绿灯信号用的，-this procedure is used in electronic police above, mock traffic light signals are used,

DS1820 C51 子程序-C51 subroutine DS1820

一个直流电机的闭环控制源代码程序，使用AVR单片机做控制，-A closed-loop DC motor control source code, the use of AVR single-chip microcomputer controlling,

智能计数器，对外部信号脉冲进行计数，并将脉冲个数显示出来。 基本要求：计数至少65536个脉冲，并将脉冲个数显示出来。 -intelligent counter, the external signal pulse counting, pulse number will be displayed. Basic requirements : at least 65,536 Count pulse, and pulse number displayed.