51 single

师哥们做的单片机键盘、液晶显示程序，汇编语言，函数算法很清晰-Division buddies to do the single-chip microcomputer keyboard, LCD process, assembly language, function algorithm is clear

P1.7～P1.0接发光二极管L8～L1，要求利用单片机内部定时器1，按方式1工作，每0.01秒T1溢出中断一次。要求编写程序模拟时序控制装置。开机第1秒钟L1、L3亮，第2秒钟L2、L4亮，第3秒钟L5、L7亮，第4秒钟L6、L8亮，第5秒钟L1、L3、L5、L7亮，第6秒钟L2、L4、L6、L8亮，第7秒钟8个发光二极管全亮，……一直循环下去。fosc=11.0592MHz-P1.7- P1.0 then LED L1 to L8, by using a timer internal microcontroller, a work by the way, every 0.01 seconds T1 interrupted an overflow. Simulation prepared timing control device. Boot 1 seconds L1, L3- liang, two seconds L2- L4, L5 three seconds, L7- liang, 4 seconds L6, L8-liang, 5 seconds L1, L2, L5, L7- liang, 6 seconds L2, L4, L6, L8- , 7 seconds 8-LED whole ... has been the cycle continues. 11.0592MHz fosc =

该时钟以24小时制显示时间，并可显示2000年至2049年之间的任何日期及星期，日期与时间经按键可相互切换，可输入8个闹钟时间设置，每个闹钟设置包括响铃的时间（小时与分钟）、对工作日有效还是对周末有效的标志，以及本项设置是否启用的标志等三部分。这8个闹钟设置均保存在EEPROM中，即使掉电也不用重新输入。-The 24-hour clock to display time, and shows from 2000 to 2049 and any date between the weeks, the date and time as may be mutually switch button, enter the eight alarm time settings, each set including the ringing of an alarm clock Duration (hours and minutes), the effective working days or weekends effective road signs, as well as whether or not to enable this setting, such as a symbol of three parts. This 8 alarm settings are stored in EEPROM, even brown-out do not have to re-enter.

用AVR编写的24小时时钟程序，还望采纳-AVR prepared with a 24-hour clock procedures, but also look to adopt

这是关于DS18B20的读写程序,数据脚P2.2,晶振12MHZ 温度传感器18B20汇编程序,采用器件默认的12位转化,最大转化时间750微秒 显示温度00到99度,很准确哦~~无需校正!-DS18B20 on literacy, data P2.2 feet, 12MHZ crystal temperature sensor 18B20 assembler, using the default device into 12, the largest 750 microsecond conversion time show that the temperature from 00 to 99 degrees, very accurate ~ ~ Oh, no correction!

lcd12864 显示汉字图片 反白,是一个非常好的程序,可以和大家共享,-lcd12864 display Chinese characters picture anti-white, is a very good process, and everyone can share,

整有效。中间四个字节分别代表设备的地址、指令类型、指令参数1(OPT1)和指令参数2(OPT2)。设备在对这四个字节的内容进行译码后执行相应的操作

简易信号发生器：有原理图，仿真图，C程序，功能比较齐全-Simple Signal Generator: A schematic diagram, simulation plans, C procedures, functions relatively complete

STC89C58RD+系列软件实现spi-STC89C58RD+ Series software spi