TELEPHONO的C51程序

EM78P447中文手册，EM78P447是很常用的义隆单片机。-EM78P447 Chinese Manual, EM78P447 Elan is very commonly used in single-chip microcomputer.

FAT16文件系统原理，较详细的说明文件，很好的资料-FAT16 file system principle, more detailed documentation, very good information

本程序是基于MFRC500射频卡读写器的单片机控制程序，所用单片机为AT89C52.-This procedure is based on RF card reader MFRC500 microcontroller control procedures, using microcomputer AT89C52.

* 功能：LPC2100的IAP功能测试。 * 说明：调用IAP服务程序，完成FLASH编程操作。 * 将paramout添加到Watch窗口，观察返回值。-* Function: LPC2100 the IAP function test.* Description: Call IAP service program, complete the FLASH programming operation.* Will paramout added to the Watch window to observe the return value.

spi prog for mcu ok in keil C

通过了硬件调试，用89c51控制18b20采集温度。而且还是简单易懂的c语言-Hardware through the debugging, use 18b20 Acquisition 89c51 temperature control. It is also easy-to-understand language c

此为18B20的温度检测以及键盘控制和液晶显示程序.好用.-18B20 This is the temperature detection and control of the keyboard and LCD display program. Easy to use.

很好的用io口模拟串口的程序，内带仿真文件，可随意修改，已经在产品中应用，可放心使用。-Io mouth with a very good simulation of serial procedures, within the simulation with documents, can be freely modified, has been applied in the product can be assured that use.

常用串行EEPROM的编程应用，Microwire总线是美国国家半导体公司研发的一种简单的串行通讯接口协议，该总线是采用三线进行数据传输。Microwire总线和SPI总线一样数据输入输出分别使用一根引线，同样可以提供同步数据传输方式，可以适用在多种微控制器、EEPROM或ADC等场合。-Commonly used application of serial EEPROM programming, Microwire bus is the United States National Semiconductor R

keilc + proteus 并行口设计指示灯实验 要求：掌握80C51单片机输入输出接口使用方法 学会开关量输入输出控制的接口技术及编程方法 实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.