这是一个功率计参数表格的程序，有兴趣的朋友可以看看，脉冲式的...

* 本程序包含控制外部液晶面板的4-BIT控制模式子 * * 程序。这些程序是专门为 MCU201 workshop演示板 * * 设计的。但它也可作为其他类型的使用 KS0066U控 * * 制器的液晶面板的控制程序。-* The procedures include external LCD control of the four-BIT- control mode** procedures. These procedures are specifically for MCU201 workshop demonstration board** design. It can also be used for other types of use** KS0066U control system for the LCD control procedures.

基于单片机的IDE硬盘控制的研究与设计.简单的介绍如何读写IDE-IDE hard drives based on single-chip control research and design. Introduce how to read and write simple IDE

stc单片机的iap程序，用c51写的，是从汇编转换过来的-SCM STC IAP procedures, using C51 write is from the compilation of the conversion from the

nrf24l01的中文说明文档，方便开发-chinese documents of NRF24L01，provide convenience for development

51单片机驱动DHT11温湿度传感器并成功在数码管上显示，压缩包内有驱动后的照片。-51 MCU-driven DHT11 temperature and humidity sensors and successfully in the digital tube display, compression packages have driven after photos.

1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.

CAN三台机子互相通讯（机子2程序），已调通，标准的标识符，11位。-CAN communication with each other three loom (loom 2 procedure), Qualcomm has been transferred, the standard identifier, 11.

PIC单片机与LCD1602的汇编程序。可以直接使用。里面PIC16和PIC18两种，注意分辨。-PIC MCU and the assembler LCD1602. Can be used directly. Inside the PIC16 and PIC18 two, pay attention to distinguish.

使用MSP430f247芯片内的ADC12模块实现单通道动态采集外部电压-MSP430f247 chip using the ADC12 module realize single-channel dynamic collection of external voltage

该时钟以24小时制显示时间，并可显示2000年至2049年之间的任何日期及星期，日期与时间经按键可相互切换，可输入8个闹钟时间设置，每个闹钟设置包括响铃的时间（小时与分钟）、对工作日有效还是对周末有效的标志，以及本项设置是否启用的标志等三部分。这8个闹钟设置均保存在EEPROM中，即使掉电也不用重新输入。-The 24-hour clock to display time, and shows from 2000 to 2049 and any date between the weeks, the date and time as may be mutually switch button, enter the eight alarm time settings, each set including the ringing of an alarm clock Duration (hours and minutes), the effective working days or weekends effective road signs, as well as whether or not to enable this setting, such as a symbol of three parts. This 8 alarm settings are stored in EEPROM, even brown-out do not have to re-enter.