万年历 megal128 iccavr开发平台

ATMEL公司的AT89系列单片机的资料，不用我多说了吧：）-ATMEL"s AT89 Series MCU information, I need not say it :)

HMC6253 interfacing with atmega

HT24 系列的EEPROM 总共8 个管脚，三个为芯片地址脚A0、A1、A2，在单片机对它进行操作时，从SDA 输入A0、A1、A2 数据和芯片外部A0、A1、A2 所接地址需一一对应。一个为芯片写保护脚WP，WP 脚接低电平时，芯片可进行读写操作；WP 脚接高时，芯片只可进行读，不可进行写。 另外两个管脚为电源脚VCC，VSS。 用单片机对HT24 系列的EEPROM 进行控制时，HT24 系列的EEPROM 的外部管脚VCC、VSS、WP、A0、A1、A2 根据需要，对应接上，SDA、SCL 接到单片机控制脚上。-HT24 Series EEPROM total of 8 pins, three pins for the chip address A0, A1, A2, in the microcontroller to operate it, from SDA input A0, A1, A2, and chip external data A0, A1, A2 of the Then one correspondence address must be in. One for the chip, write-protect pin WP, WP feet then low, the chip can be read and write operations WP pin is high then, the chip can only be read, not write. The other two pins for the power pin VCC, VSS. With the microcontroller on the HT24 Series EEPROM control when, HT24 Series EEPROM external pin VCC, VSS, WP, A0, A1, A2 according to the needs of the corresponding connected, SDA, SCL receives SCM control feet .

摩托罗拉单片机的液晶LCD显示的C语言程序-Motorola MCU LCD liquid crystal display ........... C Programming Language

本程序采用AT89C51单片机，ADC0809模数转换芯片进行模数转换，最终由数码管显示“0809**”。-This procedure using AT89C51 single-chip microcomputer, ADC0809 analog-to-digital conversion chip for analog-digital conversion, and ultimately by the digital tube displays

胶印机印刷控制程序 -Offset printing control procedures

用51引脚模拟SPI，进行ad7706读写操作。-the source code which use 51 MCU read and write ad7706

dsPIC33F型号的CPU可配置10位或12位的ADC采样，转换完成后直接从DMA中读取转换结果。源码中对多路模拟量进行采样，对ADC及DMA分别进行了配置。 -dsPIC33F models of CPU can be configured 10-bit or 12-bit sampling ADC, the conversion after the completion of DMA read directly from the conversion results. Source of multi-channel analog sampling, the ADC and DMA configuration respectively.

一个简单的利用查表法的反正切和正、余弦函数，在处理速度不快的单片机编程中，这是一个使用的方法。-The use of a simple arctangent look-up table method and positive, cosine function, the processing speed of microcontroller programming unpleasant, this is a method used.

这是用AT89C2051单片机实现模数转换的源程序，程序由汇编语言编写-This is achieved using AT89C2051 mode conversion of the source, procedures prepared by the assembly language