本人自己制作的JTAG下载线，只用了一片244,可以支持ARM9、Cortex™...

S3C2440A中IIC接口的基本操作编程，实现向AT24C02内部地址0x00~0xff依次写入数据，然后再读出并比较。-S3C2440A in the basic operation of IIC interface programming, to achieve the AT24C02 internal address 0x00 ~ 0xff followed by write data, and then read out and compare.

使用寄存器点亮led灯，是关于arm工程的，要与开发板结合使用，编程工具是keil5.

周立功公司开发的单片机手册，具体的数据手册见周立功网站下载。-Week Ligong Singlechip developed manual, the specific data manual see Zhou Ligong website.

使用ARM SAM7控制器在16位模式下使用ILI9325驱动程序驱动LCD N96。

开发环境:ADS 1.2/SDT 2.51 GUI测试，由于没有触摸屏，所以将触摸屏的代码给屏蔽了； 请将FS44B0II开发板连接好交叉网线、直连串口线、电源， 并连接好G57液晶屏，同时还要连接好背光电源； 然后在BIOS的命令窗口里面敲netrun命令； 点击FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel目录下： 批处理文件FS44B0_G57_uCGUI.BAT 下面你就可以看到液晶屏上面显示优龙标志 它会延时一两秒中进入下一个画面，逐步延时GUI的各项功能，请耐心观看； -Development Environment: ADS 1.2/SDT 2.51GUI test, because there is no touch screen, it will be touch screen to shield the code Please FS44B0II development board to connect a good cross-network lines, direct serial lines, power supply, and connect a good G57 LCD screen, at the same time, good backlight power supply connection and then in the BIOS command window knock netrun order Click FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel directory: batch file FS44B0_G57_uCGUI.BAT below you can see the LCD screen above shows excellent signs that it will delay Liuzhou 1 two seconds to enter the next screen, and gradually delay the GUI features, please be patient watch

AT9261在ADS下面的8个代码，一般网站只提供3个代码！-AT9261 in ADS the following 8 code, the general site code only 3!

阐述Bootloader实现的目的、过程、原理，结合三星S3c2410开发板的硬件特性和项目的具体需求，设计开发合理高效的启动模块，并衍生出Bootloader在NAND Flash与NOR Flash下的2种不同加载方式，针对NAND Flash和NOR Flash实现完整的启动引导程序-Bootloader on the achievement of the purpose, process, principle, combined with Samsung" s hardware development board S3c2410 characteristics and the specific needs of the project, the design of rational and efficient development of start-up module, and derived from Bootloader in the NAND Flash and NOR Flash the two kinds of different ways to load for NAND Flash and NOR Flash to achieve a complete start-up boot

ARM系列芯片嵌入式平台USB下载器的通用DLL文件，支持多种仿真器-ARM chip embedded platform

应用背景软件定时器,UCOSII消息队列,使用比较实用的软件编程思路，在实践中很受益，，，关键技术UCOSII消息队列 ，如果管理消息列队，如何做调度器，软件定时器等，能同时处理大量问题，，，，

嵌入式arm舵机控制程序，可以控制舵机完成0-180的来回旋转，嵌入式arm舵机控制程序，可以控制舵机完成0-180的来回旋转，嵌入式arm舵机控制程序，可以控制舵机完成0-180的来回旋转