使用cnpic18f452的MS320240Bled初始化，使用PIC_CCS编译

上传一份本人自己写的DS18B20读写程序 包括光刻ROM等详细部分-From a I wrote it myself DS18B20 lithography ROM reading and writing process, including details such as part of

tcp_ip协议栈的ucos代码，主要用于嵌入式系统开发，已经移植到51系统单片机中，通过keil可进行编译，ucos经过最简化改造！特别推荐-tcp_ip CENTER protocol stack code, mainly for embedded system development, has been ported to 51 SCM system, through c51 can be compiled after the most simplified CENTER transformation! Preferred!

两位数码管动态显示，两个按钮可使数码管数字调大调小-Two digital tube dynamic display, two buttons will enable the digital tube digital transfer major small

介绍了一种基于MCS251 系列单片机的温度测控电路。可对外界温度进行测 量、误差修正、判定传感器故障与高温报警, 并具有键盘控制和警情通讯显示功能。-VERY GOOD

利用51单片机做的USB 应用实例，可模拟三键滚轮鼠标，KEIL开发-use USB MCU do application, can simulate three key wheel mouse, development KEIL

12864LCD的反白显示，现在大多LCD都是两行同时显示，该源码实现了单独显示。-12864LCD anti-white display, and now most LCD are two lines at the same time revealed that the source has a separate display.

at89c2051制作的超声波测距源程序，经本人检测程序无误，测距精度在10CM以内-AT89C2051 Ultrasonic Ranging source produced by the testing procedures I correct location accuracy within 10CM

单片机c语言开发实例 包括很多实例，希望能在这里找到有用的东西！-SCM c language examples include many examples here in the hope of finding useful things!

利用动态扫描和定时器1在数码管上显示 出从765432开始以1/10秒的速度往下递减 直至765398并保持显示此数，与此同时利 用定时器0以500MS速度进行流水灯从上至 下移动，当数码管上数减到停止时，实验 板上流水灯也停止然后全部开始闪烁，3秒 后（用T0定时）流水灯全部关闭、数码管上 显示出"HELLO"。到此保持住。 设晶振频率为12MHz。-The use of dynamic scanning and Timer 1 in the digital control to show from the beginning of 765,432 to 1/10 seconds until the speed of descending down 765,398 and maintain display this number, at the same time the use of Timer 0 to 500ms the speed of light from the flowing water to Under the move, when reduced to a few digital tube stop, the experiment on-board water stop and then all the lights started to flicker, 3 seconds later (T0 regularly used) closed water lights, digital tubes show

一个采用C8051F020+CH372实现的带USB功能的流量测控系统，包括C8051F020的AD/DA/串口编程、触摸屏的串口编程、CH372实现的USB接口编程（原创）等。这些源代码已在某产品中使用。-A used C8051F020+ CH372 achieved with USB function of flow measurement and control system, including the C8051F020 the AD/DA/serial programming, the serial touch-screen programming, CH372 realized USB Interface Programming (original) and so on. These source code has been used in a product.