AT24C08在线基本读写过程中灭绝，经过委员会…

本程序运行于C8051F330，功能为接收遥控器发出的红外信号，然后等待上位机通过I2C总线来读取。IR数据接收完毕后，不再采集新的IR数据，一直等待上位机将数据取走后才开始准备接收新的IR数据-this program running on the C8051F330, functional remote control device to receive the infrared signal, Then wait for the PC through the I2C bus to read. IR data receiving end, not the acquisition of new IR data have been waiting for the PC will be removed after data began preparing to receive the new IR data

此源码是基于凌阳系列单片机编写的，主要是训练对凌阳单片机的基础。 霓虹灯为多样式变化的，可以修改源码来实现自己的想法！-This source is based on the Sunplus Series Singlechip prepared, mainly training on the basis of single-chip Sunplus. Neon lights for many style changes, you can modify source code to realize their own ideas!

低成本m48+热敏电阻做多路温度报警装置显示和音乐！

可调万年历led版:led数码显示时间及温度，时间随时可调。-Adjustable calendar led Edition: led digital display time and temperature, time adjustable at any time.

高速DDS芯片AD9851的应用程序，基于AVR128单片机最快可产生180MHZ正弦波（对PCB的要求很高！）

IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta

NEC标准遥控接收处理程序，OK的IIC通讯程序，51单片机定时中断程序-NEC Standard Remote Control Receiver processing, OK for IIC communication procedures, 51 MCU timer interrupt program

TS12864A-3汉字库。有需要的朋友请下载-TS12864A-3汉字库. Friend in need, please download

用pic18f8720做的电压采样处理程序，带了proteus仿真图的！-Pic18f8720 to do with the voltage sampling process, with the Proteus simulation chart!

能实现功能有：显示年、月、日、星期、时、分、秒、阴历月日、温度，共21位数码管。其中星期和阴历月日能根据公历自动计算改变，到2050年之前有效。温度可以测量从-10到40℃之间的温度。还可以设定两个定时、12/24小时显示、自动亮暗切换的时间等。 电路只用了两片IC，一片M48，另外一片是74LS145，4-10译码器，来扩充端口。具体电路在下面，是PROTEUS画的，给个图片做参考-To achieve functions: Display year, month, day, week, hour, minute, second, lunar month, the temperature, a total of 21 digital tube. One week and the lunar month on the Gregorian calendar automatically calculated based on changes effective prior to 2050. Can measure temperatures from-10 to 40 ℃ temperature between. Also can set two time, 12/24 hour display, automatic light switch dark time. Circuit used for only 2 IC, an M48, the other is a 74LS145 ,4-10 decoder to expand the port. Specific circuit in the following is the PROTEUS painting, a reference to a picture