登录
首页 » SCM » 51 mcu display programme

51 mcu display programme

于 2022-02-13 发布 文件大小:278.18 kB
0 185
下载积分: 2 下载次数: 1

代码说明:

51 mcu display programme-51 mcu display program

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 用51单片机c语言编写的键盘扫描程序
    用51单片机c语言编写的键盘扫描程序-With 51 single-chip c language keyboard scanner
    2022-03-02 19:27:01下载
    积分:1
  • c8051f330 uart serial
    c8051f330UART,c8051f330串口程序,大家可以试一下,-c8051f330 uart serial
    2022-03-20 07:41:09下载
    积分:1
  • 51单片机5043eeprom驱动程序源码肯定是好地,大家好好用吧!
    51单片机5043eeprom驱动程序源码肯定是好地,大家好好用吧!-51 SCM 5043eeprom driver source code is certainly well, we make good use!
    2022-10-07 18:25:03下载
    积分:1
  • pic16f877a使用iic总线方式驱动低价温度芯片tc74,并液晶显示的一个程序,板上验证通过,可以直接使用,令附tc74中文资料
    pic16f877a使用iic总线方式驱动低价温度芯片tc74,并液晶显示的一个程序,板上验证通过,可以直接使用,令附tc74中文资料-PIC16F877A using the IIC bus driven low temperature chip tc74, and liquid crystal display of a procedure to verify through the board, you can directly use, the attached information tc74 Chinese
    2022-11-18 13:30:03下载
    积分:1
  • 51 some very useful subprogram has a very good suggestion
    51的一些很有用的子程序 很好的 建议拥有-51 some very useful subprogram has a very good suggestion
    2022-11-21 16:05:04下载
    积分:1
  • * Hardware architecture: PA0
    * 硬件结构: PA0-5对应6个LED数显管的位 ,PC0-7对应各LED数显管的段 ,PB4-7为键盘。 * 软件描述: 上电后,时钟从00.00.00(时/分/秒)自动走时,在走时状态时 , 按PB4(设定 * 键)超过3秒可循环选择调整时间/工作参数 ,接着按PB5以确定选择的操作 ,进入调整操作后 , * 按PB5选择欲调整参数,按PB6(增加键)完成调整参数操作 。按PB7,进入时控运行,PB1亮, * 再按PB7停止时控运行,回显走时。在定时到时,PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov
    2022-04-16 19:29:12下载
    积分:1
  • dsp 5509a 的usb程序ATMEGA16单片机进行AD转换的源程序代码
    dsp 5509a 的usb程序ATMEGA16单片机进行AD转换的源程序代码-dsp 5509a the usb procedures ATMEGA16 microcontroller for AD conversion of the source code
    2022-03-26 11:53:37下载
    积分:1
  • 显示界面的显示程序显示 界面的显示程序
    显示界面的显示程序显示 界面的显示程序-Show interface show interface display program to display the show interface display program
    2022-04-21 20:06:46下载
    积分:1
  • SCM interrupt procedures and procedures keyboard
    单片机串口中断程序和键盘程序-SCM interrupt procedures and procedures keyboard
    2022-05-06 19:34:09下载
    积分:1
  • 这是本人最近几年所编写的串行通讯的代码集,可以供大家参考学习。...
    这是本人最近几年所编写的串行通讯的代码集,可以供大家参考学习。-recent years prepared by the serial communication code sets, we can reference for learning.
    2022-05-14 16:06:40下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载