温度控制器01

该源程序是通过对键盘的扫描方式对键盘按键的识别-The source is the keyboard scan mode by the keyboard keys to the identification of

利用yc7c68013实现了模数和数模传输，经测试，在keilc51中能通过-Yc7c68013 achieved using D and D transmission, have been tested in China and through keilc51

自己用C语言编的一个LCD显示程序，由于刚学单片机，写得功能比较简单-Own use C language compiled an LCD display program, as just learning microcontroller, written in relatively simple function

串口控制8路舵机程序,本程序适用于III型实验板，如有需要请与我联系-Serial 8-way steering control procedures, this procedure applies to type III board and, if necessary, please contact me

/************************************************************* 文件名: autocp2.c 主题: autocp-2 型智能水泵控制器程序 Ver 1.2 修改日期 2001/12/21 修改内容: 将1 型的井水位检测由井内改到水箱的出水口处, 刚开机时延时5 秒检测.-/******************************* Name : autocp2.c theme : autocp-2 smart pump controller procedures Ver 1.2 Revision Date q310703 revisions : a type of well water testing by the change to the well bore the tank outlet, the irruption of aircraft detection latency five seconds.

HT1622 单片机驱动 LCD显示驱动新片的单片机控制方法-HT1622 LCD display driver in new MCU control method

以GMS97C2051单片机为核心，采用TLC2543 12位串行A/D转换器，设计了一个串行数据采集/传输模块，给出了主要源程序。-to GMS97C2051 as the core, using TLC2543 12 serial A/D converter, the design of a serial data collection/transmission module, is the main source.

仿真步骤如下： 1、把3个帖子的内容分别保存为51t9py.c,51t9py_indexa.h,5py_mb.h，放在同一目录下，将51t9py.c加入工程编译 2、由于Keil的模拟串口是单字节显示，汉字显示为乱码，所以要加挂RICHWIN或RichView这种会重新刷新显示的中文平台，或手工刷新屏幕，所以请先到 http://www.pchome.net/dl/chinese.htm 下载RichView，安装运行 3、在Keil环境下可以直接按“Ctrl＋F5”键仿真，按“F5”全速运行，切换到在串口依次输入: // 64*.6 426***.5 98*.7 936.3 586.1 4826*.1 9464*.7 64*.6试试:-) 4、按键对应(根据我自己的手机设置的,全部在PC的小键盘操作)： -simulation steps are as follows : 1 and 3 respectively, the content of messages posted on the preservation of 51t9py.c, 51t9py_indexa.h, 5py_mb.h, on the same directory, will join the project 51t9py.c compiler 2, Keil is the simulation of single-byte Serial show , the Chinese showed gibberish, so need to add or RichView RICHWIN this show will re-set the Chinese platform, or manual refresh screen, so please download RichView http://www.pchome.net/dl/chinese.htm to install three operations in Central Keil Habitat can be directly "Ctrl+ F5" key simulation, according to the "F5" running full-speed, switched to the ser

这是一个波形选择菜单，通过开发板上的按键，选择波形，幅度，频率的等各参数，然后发送给下位机。让其产生需要的波形。-This is a waveform selection menu, through the development of on-board buttons, select the waveform, amplitude, frequency and other parameters, and then sent to the next bit plane. The need to generate the waveform.

基于C51单片机驱动舵机的程序 C语言编程可控制多个舵机-C51-based single-chip driver steering procedure C language programming can control a number of steering gear