luminary 厂家的Stellaris LM3S8962 Evaluation Board 用户手册

简易的波形发生器源代码,基于NXP LPC2368-Simple waveform generator source code, based on the NXP LPC2368

arm9-AT91RM9200开发板调试程序BasicMCIDevice方面的代码，可以直接编译测试．-arm9- AT91RM9200 development board debugging procedures BasicMCIDevice The code can be directly translated tests.

使用定时器来控制DC也调整PWM波，控制LED的光按K1，PWM值增加，DC减少，导致更暗按K2，PWM值降低，而DC的增加，导致更亮

CC2430相关的一些实验程序,开发环境为IAR,如果有兴趣的人是不错的资料.-CC2430 related to some experimental procedures, the development environment for the IAR, if those who are interested in is a good information.

硬盘MP3播放器-MEGA128-VS1001K-USB-遥控-LCD-ICCAVR代码-硬盘-支持FAT32-单面PCB 第二部分-Hard disk MP3 player-MEGA128-VS1001K-USB-Remote-LCD-ICCAVR code- hard drive- FAT32-single PCB to support the second part of

ARM详细资料-ARM detailed information

以S3C44B0X嵌入式处理器为核心的嵌入式系统硬件平台上进行LCD应用程序的开发和uC/OS-II操作系统的移植-To S3C44B0X embedded processor as the core of embedded system hardware platform LCD application development and uC/OS-II operating system transplant

2104IRQ中断C语言编程-2104IRQ interruption C Programming Language

DAvE是英飞凌科技公司的电子芯片模拟开发应用工具软件。 戴夫会帮助你在你的项目中规划你想使用的英飞凌单片机或dsp,以提供智能向导,那帮你设定芯片来工作的方式和你需要的各功能模块,自动生成C-code驱动功能与适当的单片外围设备和中断的控制。 DAvE会直接与编译器的IDE互动。-DAvE is the Digital Application Engineer from Infineon Technologies. DAvE will... - Help you program the Infineon microcontroller you want to use in your project, by offering intelligent wizards, that help you configure the chip to work the way you need it and automatically generate C-code with appropriate driver functions for all of the on-chip peripherals and interrupt controls. - Interact directly with compiler IDE s. To use DAvE you need the DAvE mother system and the DIP file for your specific microcontroller. After installation of the mother system you need to install the DIP file. For this purpose please start DAvE. Goto "View", "Setup Wizard". Select "Installation". Please note: If you run DAvE on Windows Vista, then please start the program the following way: Right click with your mouse onto dave.exe. The

此示例演示如何配置微机电系统 accelerometre 来检测加速度 X / Y 轴，以检测的单击双点击 Z 轴。程序启动后检查了 MEMS accelerometre 状态寄存器和行为，如下所示： 1.如果审计委员会移动加速检测到，则 x / Y 轴和指示灯切换根据的运动方向和速度。2.如果单击检测到，则 Z 轴 LED3 和 LED6 切换期间 3s。3.如果双击在 Z 轴上检测到所有指示灯都切换期间 3s。