这是一个键盘扫描的程序，相信想做毕业设计的同学非常想得到的哦，想要就看看吧，不好的话多提建议哦...

用于MSP430F247单片机的NOKIA5110液晶屏驱动程序-NOLIA 5110 LCD Driver For MSP430F247

使用3310液晶---数字频率计 .-Use 3310 LCD- digital frequency meter.

* BL-TFT240320-BOARD 2.8/3.2" board * LCD 240x320 3.2-inch QVGA 262k TFT-LCD module * Resolution of 240RGBx320 dots * 262k TFT Color LCD * LCD driver is SSD1289 * Touch screen controller ADS7843 * SD card slot with led card insert detection * SPI pin interface * ARDUINO pin support * Black light control with hardware or software control * 8/16-bit interface for microcontrollers * 40 pin Interface * Power input voltage 5Vdc * Frame Cover * Dimensions:68mm x 97mm - * BL-TFT240320-BOARD 2.8/3.2" board * LCD 240x320 3.2-inch QVGA 262k TFT-LCD module * Resolution of 240RGBx320 dots * 262k TFT Color LCD * LCD driver is SSD1289 * Touch screen controller ADS7843 * SD card slot with led card insert detection * SPI pin interface * ARDUINO pin support * Black light control with hardware or software control * 8/16-bit interface for microcontrollers * 40 pin Interface * Power input voltage 5

DA芯片TLC5620中文资料，该pdf以中文详细的讲述了TLC5620的各项指标及其典型应用电路-DA chip TLC5620 Chinese data, the pdf in Chinese TLC5620 detail of the indicators and their typical application circuit

该文件里包含了大量的常用经典的程序代码,可以为51编程者带来事半功倍的效果,-The document contains a number of popular classics code can be programmed for 51 brought a multiplier effect,

c8051F020 液晶显示的程序 也许有用-c8051F020 LCD procedures would be useful

modbus RTU 的C51源程序,单片机89S52,编译器keilC7.06-modbus RTU source code with c51,mcu atmel89s52,complite use keilC7.06

2051单片机的18b20温度计。有效位数为2为，程序里面以预留出小数点位，配套3位数码管即可显示。-2051 microcontroller 18b20 thermometer. 2 for the effective number of bits, the program which in order to set aside a decimal place, supporting three digital control to display.

内容为89c52单片机的基本实验 内容涵盖比较多 所采用的实验板是网上和容易找到的TX-1C。是新手比较好的参考资料-89c52 microcontroller content covers the basic experiments are more used in experimental board is easy to find online and the TX-1C. Is a good reference novice

6段数码管分别显示，时，分，秒，四个按键，K1（P0.0），K2（P0.1）， K3（P0.2），K4（P0.3），四个按键用来调时间的，按下K1，所有位都清零显示，然后按下K2，秒在闪烁，继续按K2分闪烁，不段地按K2 秒--分--时切换着闪烁，在某位闪时按下K3相应位加一，确认调整，按K4，取消调整再按K1。在K1按下以后才有调时的功能，如果K1没有按下，按别的键没有反映。这为了在加点按键功能留着用 -6 respectively of the digital control, when, minutes and seconds, four keys, K1 (P0.0). K2 (P0.1), K3 (P0.2), K4 (width), the four keys to the transfer time, press the K1, All spaces are reset, then press K2, the scintillation seconds, according to K2 pm flickered. not according to K2 of seconds-- minutes-- when switching to flicker in certain press the flash-K3 corresponding increase in a confirmed adjustment by K4, then canceled K1 adjustment. K1 in the press will only be made after the transfer of function, if K1 pressed by other key is not reflected. This points to the function keys used Retention