利用ADC12内部温度传感器测量室温，并将测量结果显示在数码管上...

设计程序使一个LED发光管以0.6秒为周期闪烁，即发光管每0.3秒点亮或熄灭一次。 分析题目要求，主要涉及两方面的操作，即控制LED发光管的亮灭以及定时0.3秒。对于LED发光管，只用一个IO就可以控制了（例如使用IOA0）；而对于0.3秒定时，我们可以利用TimerA定时器轻易地实现。-The design process of a LED to LED blinking 0.6 seconds for the cycle, that is, every 0.3 seconds LED lit or extinguished once. Analysis of the subject requirements, mainly related to two aspects of the operation, that is, control LED LED light out as well as the timing of 0.3 seconds. The LED light-emitting tube, only one can control the IO (such as the use of IOA0) and for 0.3 seconds from time to time, we can use to easily achieve TimerA timer.

16x2字符液晶调试程序，在硬件上完全实现．-16x2 character LCD debugging procedures, the hardware fully realized.

这是C8051F020的源程序，很好，此单片机的功能强大，编程易学。-This is the source C8051F020, well, this single chip a powerful, easy to learn programming.

使用单片机C8050F330对无线发射接受模块进行配置与控制,使组件成为一个无线通讯中的基站.-The use of single-chip wireless C8050F330 launch module configured to receive and control, so that components into a wireless communications base station.

计算机简单控制由软件和硬件组成。软件由Visual Basic 6.0编写。硬件主要由无线发送模块和单片机（C语言编写）构成。通过RS232界面与PC通信而实现无线控制系统。 主要功能是：通过遥控器连接PC机的"上下左右"按键 ,当电脑界面处于powerpoint界面下,能通过遥控器控制幻灯片的上下切换. -Simple control by the computer software and hardware components. Software prepared by the Visual Basic 6.0. Hardware mainly by the wireless sending module and single chip (C language) constitute. Through the RS232 communication interface with the PC wireless control system. Main function is to: Connect PC through a remote control machine up and down about button, when the computer interface in a powerpoint interface via remote control to switch slides up and down.

固态继电器G3CN的中文资料。包括性能指标-Solid State Relays G3CN the Chinese data. Including performance indicators

香港科大机器人资料 单片机相关知识，开发平台多样-HKUST Information Singlechip robot-related knowledge, development platform for diverse

非接触式ic卡读写程序,希望对大家有帮助-Non-contact ic card reader program, and they hope to have everyone help

16位单片机xc164用于QH2001显示。-16 Singlechip XC164 for QH2001 show.

1.Ｋ１作为左转弯开关，Ｋ２作为右转弯开关。Ｌ１、Ｌ２作为左转弯灯，Ｌ５、Ｌ６作为右转弯灯。 2.程序实现的功能：向上打Ｋ１时左转弯灯以一定频率闪烁，打Ｋ２时右转弯灯以一定频率闪烁，Ｋ１、Ｋ２同时向上或向下，发光二极管灭。-1.K1 as a left turn switch, K2 as a switch and turn right. L1, L2 as a left turn lights, L5, L6 as lights and turn right. 2. Program features: K1 when the left turn up to fight a certain frequency of flashing lights, turn right when playing K2 to a certain frequency of flashing lights, K1, K2 upward or downward at the same time, anti-light-emitting diodes.