LCD module times expected 12,864 Chinese

遥控小汽车的设计 可以有限速区和加速区 对他完全实现自动控制-remote control cars designed to be limited to the speed zones and accelerating the full realization of his control

停车场仿真程序仿真原理：首先有两个定时器自动的随机产生请求入场的卡号和请求出场的卡号，然后剩余的事件都由处理场务事件来处理了。处理场务事件相当于一个车场总指挥。当他发现有卡号请求入场时他会决定该卡是否符合入场条件，如果不符合，直接丢掉该卡号，准备处理下一个卡号。否则看车库是否已满和车库过道是否空闲，如果车位没有满且过道是空的，则允许该车入场，并在此时将车场的最左面的空车位分给他使用。剩下的事就是让车通过过道和进入车位，并及时关闭车场入口。如果过道是空的而且又没有入场请求，则处理出场请求，首先是将车辆从车位上移到过道上，并向出口行驶，然后在出口出判断卡是否符合出场条件，如果符合则发出抬出场杆命令，允许其出场。否则让该车返回车位。程序运行时会写运行日志，在阅读本文后，相信能理解运行日志的内容-err

the sample file for C or C-the sample file for C or C++

C8051F023的应用，主要功能是通过串口1读取GPS接收机信号，在有INT0的响应时，通过串口2发送。-C8051F023 applications, the main function is to read through a serial GPS receiver signal, INT0 in response, sent through the serial port 2.

pt2240 Datasheet only.

基于UCOS-II制作的MP3，把UCOS-II移植到单片机上-based UCOS-II production of MP3, UCOS-II transplant MCU

本系统参照片上系统的设计架构、采用FPGA与SPCE061A相结合的方法，以SPCE061A单片机为进程控制和任务调度核心；FPGA做为外围扩展，内部自建系统总线，地址译码采用全译码方式。FPGA内部建有DDS控制器，单片机通过系统总线向规定的存储单元中送入正弦表；然后DDS控制器以设定的频率，自动循环扫描，生成高精度，高稳定的5Hz基准测量信号。-The system with reference to the design of system-on-chip architecture, used a combination of FPGA and SPCE061A approach to SPCE061A Singlechip for process control and scheduling core mission FPGA for external expansion, internal self-system bus, address decoding using the entire translated code approach. DDS has built internal FPGA controller, microcontroller through the system bus to the provisions of the storage unit into the sine table DDS controller and then to set the frequency, automatic cycle of scanning, to generate high precision and high stability of the baseline measurement 5Hz signal.

详细介绍了pic单片机c语言编程的方法和技巧-detail the pic microcontroller c language programming methods and techniques

用单片机控制电动车的起停，用C语言编程，编译环境是KAIL C ，选用的芯片是PIC芯片。编译很好。-SCM control of electric vehicles with the start-stop, using C language programming, compiler environment is KAIL C, use the chips are PIC chips. Compile good.

单片机linbus通讯-Single-chip communication linbus