登录
首页 » 嵌入式系统 » 44B0modbus_ascii程序要的

44B0modbus_ascii程序要的

于 2022-01-25 发布 文件大小:3.49 kB
0 205
下载积分: 2 下载次数: 1

代码说明:

44B0modbus_ascii程序要的-44B0modbus_ascii procedures to the

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 飞利浦10碟VCD控制程序
    飞利浦10碟VCD控制程序--Control program for Philips 10-disk VCD.
    2022-07-11 13:17:37下载
    积分:1
  • arm on the gprs communication module, the test can be oh, want to be useful to y...
    arm上的gprs通信模块,测试可用哦,希望对你有用啦。-arm on the gprs communication module, the test can be oh, want to be useful to you啦.
    2022-03-12 14:24:16下载
    积分:1
  • 新手开发的一PDA程序,基于window ce .net
    新手开发的一PDA程序,基于window ce .net -Procedures for the development of a PDA novice
    2022-08-16 02:27:39下载
    积分:1
  • 我用BASIC开发环境下的LED屏单显示实验程序,可以初步了解下B环境下SPI的简单应用...
    我用BASIC开发环境下的LED屏单显示实验程序,可以初步了解下B环境下SPI的简单应用-I use BASIC development environment under a single LED screen shows the experimental procedure, can be a preliminary understanding of B under the simple application of SPI
    2022-02-03 19:16:00下载
    积分:1
  • CC2520 Tranreceive 例程
    海, 我已添加变送器 CC25xx 例程进行测试。
    2023-02-09 04:10:04下载
    积分:1
  • 触摸调光
    资源描述用电阻给电容充电,当手触摸到与电容连接的金属片时,电容大小发生改变,从而改变电容充电时间。利用单片机不断检测电容充放电时间即可检测有无触摸,利用PWM进行无极调光。
    2022-01-26 02:35:35下载
    积分:1
  • 在GNU上开发的应用程序源代码
    在GNU上开发的应用程序源代码-GNU on the development of the application source code
    2022-01-22 05:14:52下载
    积分:1
  • freescale ep100 PWM程序,按程序在初始化有限..
    freescale ep100 PWM 程序,按程序中代码初始化即可启动使用PWM,代码已经经过调试。-freescale ep100 PWM process, according to the procedure in the initialization code to activate the use of PWM, the code had already been debugging.
    2023-04-22 18:30:04下载
    积分:1
  • msp430f169 the spi procedures, very useful, we must look at ah
    msp430f169的spi程序,很有用的,一定要看啊-msp430f169 the spi procedures, very useful, we must look at ah
    2023-02-24 04:20:03下载
    积分:1
  • Xilinx IIC IP
    由 Xilinx 提供的 IIC 接口,使用 AXI interface。 Features ‧ AXI interface is based on the AXI4-Lite interface ‧ Master or slave operation ‧ Multi-master operation ‧ Software selectable acknowledge bit ‧ Arbitration lost interrupt with automatic mode switching from master to slave ‧ Calling address identification interrupt with automatic mode switching from master to slave ‧ START and STOP signal generation and detection ‧ Repeated START signal generation ‧ Acknowledge bit generation and detection ‧ Bus busy detec ‧ Fast mode 400 KHz operation or standard mode 100 KHz ‧ 7-bit or 10-bit addressing ‧ General call enable or disable ‧ Transmit and receive FIFOs - 16 bytes deep ‧ Throttling ‧ General purpose output, 1 bit to 8 bits wide ‧ Dynamic Start and Stop generation ‧ Filtering on the SCL and SDA signals to eliminate spurious pulses
    2023-09-07 01:15:03下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载