移植的ARM9，S3C2410版本的jm86，开发环境是ADS，优化的不多，可以跑，QCIF的效果还OK...

本程序实现用数码管来显示由电脑串口发来的数据。-This procedure to achieve with digital control to display sent by the computer serial port data.

自动往返小汽车程序，感兴趣的可以看看，不错的哦！-Automatically from the car program, interested can look at, oh, good!

每次开机都将次数加1 并存储到EEPROM。这样就能直观的看到机器的使用次数。用P1口 LED做为显示，次数大于256是将溢出，按复位模拟开机 或者直接通过开关开机。-Each boot will add a number of times and stored in EEPROM. This will be able to see the intuitive usage of the machine. As with the P1 port LED display, frequency is greater than 256 is the overflow, according to reset the boot, or directly through the analog switch boot.

本例为嵌入式linux平台下的串口开发实例，开发原始平台为华恒HHPPC860-3COM-2ETH-R1，可根据需要进行修改。-the cases for embedded Linux platform under development Serial example, development of the original platform for huaheng HHPPC860- 3COM- 2ETH-R1, may need to be modified.

通过对计算机的组织与结构的分析，综合运用所学计算机原理知识，设计并实现较为完整的计算机，即模型机。它可以完成一般计算机的最基础功能，具备16条基本指令，以及4种寻址方式等。并且，计算机数据通路的控制将由微程序控制器来完成，CPU从内存中取出一条机器指令到指令执行结束的一个指令周期全部由微指令组成的序列来完成，即一条机器指令对应一个微程序。设计过程包括四个部分：㈠模型机硬件组成分析；㈡指令系统设计；㈢微程序设计；㈣上机实现，示范程序。- Through to the computer organization and the structure analysis, the synthesis utilization studies the computer principle knowledge, designs and realizes a more complete computer, namely molding machine. It may complete the common computer the most foundation function, has 16 elementary instructions, as well as 4 addressing ways and so on. And, the computer data path control will complete by the microprogram controller, CPU will take out a machine instruction from the memory a instruction cycle which finished to the instruction execution completely the sequence which will be composed by the microcode to complete, namely a machine instruction will correspond a microprogram. Design process including four parts: (1) Molding machine hardware composition analysis;

嵌入式入门笔记，网络编程，使用Linux系统等，pdf格式-Embedded entry notes, network programming, the use of Linux systems, pdf format

公司开发的CATV网管系统Rabbit2000的源程序-developed by CATV Network Management System Rabbit2000 the source

linux下，与s3c2410连接的前端衰减器pe4302驱动程序，用于控制模拟信号的衰减量。-linux with S3C2410 connect the front-end attenuator pe4302 drivers, analog signal used to control the attenuation.

这是一个AD转换程序，适合新手入门使用，简单易学，本人就是从这个简单例程开始学习AVR单片机， 希望对新人有帮助-This is an AD conversion process, suitable for beginners to use, easy to learn, I was from the beginning of learning this simple routine AVR microcontroller, would like to help newcomers

cc2430zigbee的通信程序 能够实现点对点的通信-cc2430zigbee communication programme.