c3p0所需要的所有jar包以及mysql驱动包.rar

三维定位chan_taylor，针对数学建模设计，matlab代码。简单修改参数可直接使用，注释清晰

可以在 opencv安装目录opencvsourcesdata中找到。方便大家下载，故上传在这里。人脸检测，人脸识别，人眼检测，鼻子检测，嘴检测等等训练好的xml文件

针对轨迹序列 长度 不固 定 的特 点,计 算轨 迹 间的 距离。采用K均值算法对轨迹样本进行聚类。

隔离型双向dcdc变换器，单移相控制方式，结构比较基础，可以参考，用pscad4.5搭的

软件 博途，本系统控制六层电梯， 采用集选控制方式。 为了完成设定的控制任务， 主要根据电梯输入/输出点数确定PLC 的机型。 根据电梯控制的要求， 电梯应具有内呼和外呼按钮、 行程开关、 开关门按钮， 以及相应的指示灯， 估算所需 I/O 口的数量

文档主要描述四叉树的思想的原理，能清除的给读者知道四叉树的来龙去脉，因此，不懂此原理的朋友可下载。

频谱仪的介绍、操作及性能指标，硬件工程师必须学会的测量器件之一。Definitions and conditionsSpecifications describe the performance of parameters covered by the productwarranty and apply to the full temperature of 0 to 55C, unless otherwisenotedGet more Information95th percentile values indicate the breadth of the population (approx. 2 o) of perfor-This EXA signalanalyzer datamance tolerances expected to be met in 95 percent of the cases with a 95 percentsheet is a summary of theconfidence, for any ambient temperature in the range of 20 to 30C. In addition tothe statistical observations of a sample of instruments, these values include thespecifications and conditionseffects of the uncertainties of external calibration references these values are notfor N9010A EXA and N9010AEPwarranted. These values are updated occasionally if a significant change in theExpress EXA signal analyzers.statistically observed behavior of production instruments is observedwhich are available in the EXASignalAnalyzer SpecificationTypical describes additional product performance information that is not covered byGuide(N9010-90025)the product warranty It is performance beyond specifications that 80 percent of theunits exhibit with a 95 percent confidence level over the temperature range 20 toFor ordering informationkrefer30C. Typical performance does not include measurement uncertaintyto the EXA Signal AnalyzerConfiguration GuideNominal values indicate expected performance, or describe product performance59896531Nthat is useful in the application of the product, but are not covered by the productwarrantyThe analyzer will meet its specifications whenIt is within its calibration cycleUnder auto couple control, except when Auto Sweep Time rules= AccySignal frequencies 10 MHZ, with DC coupling appliedThe analyzer has been stored at an ambient temperature within the allowedoperating range for at least two hours before being turned on; if it had previouslybeen stored at a temperature range inside the allowed storage range, but outsidethe allowed operating rangeThe analyzer has been turned on at least 30 minutes with auto align set tonormal, or, if Auto align is set to off or partial, alignments must have been runrecently enough to prevent an Alert message; if the Alert condition is changedfrom Time and Temperature to one of the disabled duration choices, the analyzermay fail to meet specifications without informing the userFor the complete specifications guide, visitwww.agilent.com/find/exaspecifications1. For earlier instruments/Serial number prefix MY/SG/US5052), the full temperature rangesfrom5t50°CFrequency and Time specificationsFrequency rangeDC coupledAC coupledOption 50310 Hz to 3.6 Gh10 MHz to 3. 6 GHzOption 50710 Hz to 7 GH10 MHz to 7 GHzOption 51310 Hz to 13.6 GHz10 MHz to 13.6 ghzOption 52610 Hz to 26.5 GH10 MHz to 26.5 GhzOption 53210 Hz to 32 gHzNAOption 54410 Hz to 44 gHzNABandLO multiple(N)10 Hz to 3. 6 GHz3.5to7.0GH3.5to8.4GH28.4 to 13.6 GHz3135to17.1GH17 to 26.5 GHz5426.4 to 34.5 ghz344t044GHzFrequency referenceAccuracy+l time since last adjustment x aging rate)+ temperature stability t calibrationaccuracyAging rateOption pFrStandardy±1×106/year±15X107/2 yearsTemperature stabilityOption PFrStandard20to30°c±15×108±2×106Full temperature range±5x1±2×10Achievable initial calibration accuracyOption PFrStandard±4x108±1410Example trequency reterence accuracy=±(1×107+5×103+4×10-)(with Option PFR1 year after last adjustment±19x10Residual fmOption pFr

信号处理； EMD；相关系数；Hilbert；包络谱 信号处理； EMD；相关系数；Hilbert；包络谱

【实例简介】KICA的详细代码，包含高斯核，多项式核等多种核函数

对jaffe人脸库进行识别测试，将jaffe人脸库分为训练集和测试集两部分，首先对图片进行LBP+LPQ特征提取，然后svm分类识别，统计识别率