systemblockdiagram.pdf

DFT：离散傅立叶变换 符运行后得频谱图(DFT: Discrete Fourier Transform running at a frequency spectrum)

说明：  完整版的MATLAB视频播放程序代码说明文字(The full version of MATLAB video player )

matlab所有的函数整理工具书,基本所有常用的函数都可以查找到。(a book includes All functions of Matlab)

l1-magic的matlab代码，l1-magic: Recovery of Sparse Signals via Convex Programming(l1-magic of matlab code, l1-magic: Recovery of Sparse Signalsvia Convex Programming)

该压缩包包含了“信号与系统分析及MATLAB实现”一书的所有程序； (The archive contains a " signal and system analysis and MATLAB to achieve" a book of all programs )

以最小均方算法为约束条件的自适应波束形成(Adaptive beamforming with the minimum mean square algorithm as the constraint)

problem 5.19 rappaport

the code contain iris recognition code

传统的宽带信号中抑制正弦干扰的方法是采用陷波器(notch filter),为此需要精确知道干扰正弦的频率.然而当干扰正弦频率是缓慢变化时,且选频率特性要求十分尖锐时,则最好采用自适应噪声抵消的方法.下图是用一个二阶FIR的LMS自适应滤波器消除正弦干扰的一个方案。该代码实现了以下功能： 1) 借助MATLAB画出了滤波器的误差性能曲面和误差性能曲面的等值曲线； 2） 给出了最陡下降法以及LMS算法的计算公式； 3） 用MATLAB产生了方差为0.05, 均值为0白噪音S(n)，并画出某次采样得到的波形； 4） 根据 2）中的公式，并利用 3）中产生的S(n)，在 1）中的误差性能曲面的等值曲线上叠加画出了采用最陡下降法以及LMS法时H(n)的在叠代过程中的轨迹曲线； 5）用MATLAB计算并画出了LMS法时误差随时间n的变化曲线（对应S(n)的某一次的一次实现）和e(n)波形； 6）在 1）中的误差性能曲面的等值曲线上，叠加画出采用LMS法得到的100次实验中的H(n)的平均值的轨迹曲线； 7）最终对结果进行了分析，具体见压缩包的word文档。 (Wideband signal in the conventional sinusoidal interference suppression method is the use notch filter (notch filter), this requires precise knowledge of the frequency of a sinusoidal interference . However, when the interference frequency sinusoidal changes slowly , and the selected frequency characteristic requirements are very sharp , then best use of adaptive noise cancellation method . following figure is a second-order FIR LMS adaptive filter to eliminate a program sinusoidal interference . The code implements the following functions:   A ) draw with MATLAB error performance of the filter surface and the surface contour error performance curve 2 ) gives the steepest descent method and the LMS algorithm formula 3 ) generated using MATLAB variance of 0.05 with a mean of 0 white noise S (n), and draw a particular sampling waveform 4 ) based on 2 ) of the formula , and use 3 ) generated in S (n), in a ) the error performance curves superimposed on the surface contour pl)

16 点qam的调制解调simulink 文件(the modulation and demodule of QAM in simulink)