VSG_wuyuan_OK_2

matlab连接安捷伦示波器，可以显示单个通道数据，自己设置采样点数，设置内存深度，可以通过改变循环达到长时间监控目的（数据传输有延时，用于捕捉信号时要延长监控时间）。(matlab Connect the agilent oscilloscope)

说明：  本模型采用abaqus自带的connector连接单元建模，实现了钉节点的模拟(In this model, the connector unit of ABAQUS is used to simulate the nail node)

对动态系统辨识理论做了概括性的介绍，包含了常用的非参数系统辨识方法和参数辨识方法，并将神经网络人工智能算法应用到复杂系统参数识别，适用于系统控制、参数识别与数据预测等领域的学习。传统方法与现在智能算法都配有实例，每个代码文件都有详细注释。(This paper gives a general introduction to the dynamic system identification theory, including commonly used non-parametric system identification methods and parameter identification methods, and applies neural network artificial intelligence algorithms to complex system parameter identification, which is suitable for system control, parameter identification and data prediction. Learning in other fields. Both traditional methods and current smart algorithms are equipped with examples, and each code file has detailed comments.)

用于随机粗糙面建模的蒙特卡罗算法程序包含一维和二维算法(Monte Carlo algorithm for random rough surface modeling)

本文首先分析了永磁同步电机矢量控制的发展概况，然后从机电能量转换的角度出发，解释三相永磁同步电机的机电能量转换原理，推导拉格朗日运动方程。此外，列写出永磁同步电机在三相静止坐标系和dq坐标系下的数学模型。基于Simulink建立了转速电流双闭环矢量控制系统的仿真模型，通过对仿真结果分析，验证了永磁同步电机矢量控制系统性能的优越性。(This paper first analyzes the development of permanent magnet synchronous motor vector control, and then explains the electromechanical energy conversion principle of three-phase permanent magnet synchronous motor from the perspective of electromechanical energy conversion, and deduce the Lagrange motion equation. In addition, the mathematical model of permanent magnet synchronous motor (PMSM) in three phase stationary coordinate system and dq coordinate system is listed. Based on Simulink, a simulation model of speed and current double closed loop vector control system is established. By analyzing the simulation results, the performance of PMSM vector control system is verified.)

基于hypermill 10的五轴后处理转换器，优化了算法，中文界面。支持多种结构的五轴机床刀路仿真，输出高质量刀路。是五轴雕刻机的必备后处理转换器。(Based on the hyperMILL 10 five axis post processing converter, the algorithm, the Chinese interface is optimized. Support a variety of structure of the five axis machine tool path simulation, output high quality tool path. It is the necessary post-processing converter for the five axis engraving machine.)

说明：  用Fortran语言编写的abaqus，Dflux热源子程序，路径为环形路径(Abaqus, Dflux heat source subroutine written in Fortran language, with a circular path)

说明：  本程序是完成网络的评价路径长度和聚类系数的计算。(This program is to calculate the average path length and clustering coeffient of a network.)

说明：  abaqus中用fortran编写的热源子程序（双椭球）(Subroutine of heat source (double ellipsoid) written by Fortran in ABAQUS)

基于SAR-ADC的DAC模块的电容切换，所做的动态功耗仿真，比较了不同切换模式的功耗。(Capacitance switching of DAC module based on SAR-ADC is simulated and power consumption of different switching modes is compared.)