jinl

基于STM32的16位DAC8811驱动程序，亲测可用(STM32-based 16-bit DAC8811 driver, pro-test available)

PSCAD风机（异步机带桨距角控制）经过0.69kV-13.8kV-115kV-345kV三级升压，远距离电缆并入主网模型(PSCAD wind )

说明：  单片机I/O口控制红外发射管，模拟格力空调遥控器的代码。典型应用：上位机发送一个通用的“开机，温度，模式……”命令，单片机自动发射出和遥控器一摸一样的波形，实现智能遥控器的功能。 (MCU I/O port control infrared emission control, analog Gree air conditioner remote control code. Typical applications: host computer to send a generic &quot boot, temperature, mode ... ...&quot command, microcontroller and the remote control automatically emit the same wave first touch, intelligent remote control functions.)

单片机串口通信的应用，通过串口，我们的个人电脑和单片机系统进行通信。 个人电脑作为上位机，向下位机单片机系统发送十六进制或者ASCLL码，单片机 系统接收后，用LED显示接收到的数据和向上位机发回原样数据。(Single-chip serial communication applications, through the serial port, our personal computers and SCM systems to communicate. PC as a PC, send down bit microcontroller system or ASCLL hexadecimal code, after receiving the SCM system with LED display received data and sent back up crew as data.)

编写的飞思卡尔的sd卡读写程序，可以完成对sd卡的扇区读写，效率高，执行速度快(Writing the freescale sd card reading and writing program, can complete the sd card to the sector, speaking, reading and writing, high efficiency, the execution speed)

本方案是基于富士通高可靠性单片机开发的锂电池电动螺丝刀，采用直流无刷电机作为核心，配合方波驱动以及闭环控制技术，实现电动工具的可靠运行。 技术参数 1）采用日本富士通MCU，性能稳定，抗干扰强，高可靠性； 2）直流18V输入（可兼容不同锂电池10V—36V）； 3）三相霍尔直流无刷电机驱动，转速高达25000转/分； 4）采用德国英飞凌高性能MOS/IGBT，驱动功率高达800W； 5）高亮LED照明，工作时点亮，不工作时自动熄灭； 6）采用智能控制技术实现待机（不工作时）功耗为 0 消耗； 7）通过软件实现软启动，启动时间可调整，瞬间（1S）达最高速； 8）具有过流保护、堵转保护、过压欠压保护； 9）带速度设置按键、正反转按键、调速开关； (The program is based on the Fujitsu MCU development of high reliability lithium battery electric screwdriver, brushless DC motor as the core, with the square wave drive and closed-loop control technology, power tools for reliable operation.)

ISL94212单芯片应用代码，包括读取12串单体电池电压，温度，均衡功能，本例以s12单片机为例(ISL94212 single-chip application code, including reading the 12 series of single cell voltage, temperature, balance function, in this case in order to s12 microcontrollers, for example)

Infi-90读写测试，在安装有COPOSER的计算机上可以运行，采集ABB DCS的控制逻辑块上的数据。(Infi- 90, speaking, reading and writing test, the installation of COPOSER can run on a computer, the data on the acquisition of ABB DCS control logic block.)

无线通讯nrf905，很适合初学者来学习，里边包括了对射频寄存器的设置什么的(Wireless communication nrf905, it is suitable for beginners to learn, inside contains the settings for RF registers what)

电子时钟程序，简洁明了，原创请勿抄袭 适用于stc15单片机(Electronic clock program)