-
1602LCDa
说明: 1602LCD显示程序,自己刚刚学会编的,分享一下,谢谢!!!(1602LCD display program, their series had just learned, to share, thank you! ! !)
- 2010-04-17 23:16:10下载
- 积分:1
-
CSparse.tar
direct sparse solver for linear equations
- 2014-01-02 20:05:09下载
- 积分:1
-
Infrare-Decoder
用单片机对遥控器实现解码,并在数码管上显示(Infrare Decoder)
- 2011-08-02 16:30:30下载
- 积分:1
-
Tsq
一个水轮机调速的控制程序,想从事控制方面程序设计的朋友可以参考一下。(a turbine governor control procedures to control in the design process can make reference to a friend.)
- 2020-09-08 21:18:03下载
- 积分:1
-
pro_dds
说明: 基于STC51单片机,实现dds的算法部分(Based on 51, the algorithm part of the realization of dds)
- 2010-05-03 15:54:17下载
- 积分:1
-
123
本设计主要实现用按键控制步进电机四相单拍、四相双拍和四相八拍三种方式切换,
正、反转及其加、减速,并能在LCD上显示其运行状态(速度和转向)。(The design of the main keys to achieve control of stepper motor with a single shot four-phase, four-phase two-and four-phase eight-shot shoot three ways to switch
Positive, reverse its acceleration, deceleration, and in its operational status on the LCD display (speed and steering).)
- 2011-12-02 20:11:19下载
- 积分:1
-
ct46
说明: 计算不同的三分CANTOR集,可以由此验证WTMM的正确性(CANTOR different set of one-third can thus verify the correctness of WTMM)
- 2009-08-09 10:25:35下载
- 积分:1
-
liushuideng
51单片机5种流水灯花样,供新手学习参考~(51 SCM 5 light water pattern for novice learning reference to)
- 2012-09-25 15:37:57下载
- 积分:1
-
Sample_AgilentVISA
基于VISA的,采用lan口通信的,安捷伦示波器读取数据的程序。(VISA-based, using the lan port communications, Agilent oscilloscope program to read the data.)
- 2016-01-12 18:48:53下载
- 积分:1
-
DTMB_Modulator1111
本总体方案完成国标GB20600-2006数字电视地面广播传输系统基带部分功能。 输入数据码流经过扰码器(随机化)、前向纠错编码(FEC),然后进行比特流到符号流的星座映射,再进行交织后形成基本数据块,基本数据块与系统信息组合(复用)后并经过帧体数据处理形成帧体,帧体与相应的帧头(PN序列)复接为信号帧(组帧),经过基带后处理转换为输出信号(8MHz带宽内)。该信号经变频转换为射频信号(UHF和VHF频段范围内)。用C程序设计了图形交互界面,可以在界面上直接设置调制参数。(The overall program completion GB GB20600-2006 digital terrestrial television broadcasting transmission systems baseband function. The input data stream through the scrambler (randomization), forward error correction (the FEC), then the symbol constellation mapping bitstream to the stream, and then after forming the basic block interleaving, the basic data block and information combined system ( multiplexing) after data processing and after the frame body forms a frame body, frame body with a corresponding header (PN sequence) multiplexed signal frame (framing), after post-processing baseband signal is converted to an output (internal 8MHz bandwidth). The signal is downconverted to a radio frequency signal (in the VHF and UHF frequency range). C program designed graphical interface, you can set modulation parameters directly on the screen.)
- 2021-01-29 23:48:41下载
- 积分:1