1.3.2 连续信号采集.vi

自从NI-DAQmx 发布以来，NI 数据采集(DAQ)用户就充分利用了它的许多特性，这些特性是为节省开发 时间和提高数据采集应用程序的性能而设计的。 一个能节省相当大一部分开发时间的特性是NI-DAQmx 应用程序编程接口（API），它在各种设备功能 和设备系列中都是相同的。这就意味着一个多功能设备的所有功能可由同样的函数集编程得到（模拟输 入、模拟输出、数字I/O 和计数器）。而且，一个数字I/O 设备和一个模拟输出设备都可使用相同的函 数集编程得到。在LabVIEW 中，由于多态机制，因而这是可以实现的。一个多态的VI 接受各种数据类 型以用于一个或多个输入和/或输出终端。NI-DAQmx API 在它所支持的所有编程环境中也是保持一致 的。您仅仅需要学会如何使用一个单一的函数集就可以在多种编程环境中对大部分NI 数据硬件进行编 程。 (Since the release of NI-DAQmx, NI data acquisition (DAQ) users take full advantage of its many features, these characteristics are developed in order to save Time and designed to improve the performance of data acquisition applications. A large part of the development time-saving features a NI-DAQmx application programming interface (API), which function in a variety of equipment And equipment series are the same. This means that all the functions of a multifunction device by the same set of functions programming (analog input Into, analog output, digital I/O and counter). Moreover, a digital I/O device, and an analog output device can use the same letter Number set programming to get. LabVIEW, polymorphism, and thus can achieve. A polymorphic VI to accept a variety of data classes Type for one or more input and/or output terminals. NI-DAQmx API it supports all programming environment is consistent s. You just need to learn how to use a single set of functions can)

说明：  通过labview实现停车收费系统，包括串口的选取、读取收费卡号，初始化钱包，进行充值，扣钱，显示余额等功能。(Through LabVIEW, the parking charge system is realized, including the selection of serial port, reading charge card number, initialization of wallet, recharge, deduction, display of balance and other functions.)

1）本程序为高压电气设备局部放电领域中的信号源软件模拟程序。2）本人亲自编写。实验室一直在用。3）可模拟各种类型的放电信号。4）算法此处就不提供了，否则过于泄密了。(A) the procedures for the high-voltage electrical equipment in the field of partial discharge source software simulation program. 2) I personally prepared. Laboratory has been in use. 3) to simulate various types of discharge signal. 4) algorithm is not provided here, otherwise too leaked it.)

并在Labview上实现了滑模控制器，利用roboRIO可实现对2自由度脚踝康复机器人的实时控制。(The sliding mode controller is implemented on Labview, and the real-time control of the 2 degree of freedom ankle rehabilitation robot can be realized by using roboRIO.)

labview旋转机械轴心轨迹的子程序。(labview Frequency division amplitude)

说明：  能够进行多个通道的温度信息的采集，并且显示(It can collect and display temperature information of multiple channels)

是一个RS232串口实验报告,我自己写的,有代码,已经仿真通过了.(is an RS232 serial experiment, I wrote it myself, code, simulation has been passed.)

设置电源的电压值的控制程序，可以实现电源的任意给值，和开关控制(Setting the voltage value of the power supply control program, can achieve any of the power supply to the value, and a switch control)

基于Labview的电子钢琴设计，通过对声音频率的设置，实现发声及演奏功能(Labview-based electronic piano design, set to the frequency of the sound, vocal and performance features)

using labview to open camera