Quectel_MC20_Hardware

说明：  OLED驅動程序 (STM32 平台), 新版SPI 接口 OLED模块！ CS(片选，已接地，不用接) RET（复位）(OLED Driver (STM32 Platform))

这是一本完整的软件构建手册，涵盖了软件构建过程中的所有细节。(This is a complete software build manual covers the software build process all the details.)

汽车GPS 跟踪系统,并超速防盗报警,8051代码(Car GPS tracking system, and speeding burglar alarm, code 8051)

说明：  内涵STM8S的库，集成个人修改的文件 已经检验(Library of Connotation STM8S)

给nRF24Z1配置寄存器的软件，方便大家开发，就不用到处在数据手册中找了(NRF24Z1 software configuration register to enable easy development, do not need to look everywhere in the data sheet was)

Source code for controlling servo motor using AVR ATmega128 microcontroller. This code using timer interrupt handler. This file is for codevision avr.

在下的毕业设计，　　　本题要求设计一个直流电机控制系统。在设计中，采用国产单片机中目前比较新式的STC12C5A60S2作为整个控制系统的控制电路的核心，因为STC12C5A60S2内部有PCA模块，可以产生PWM波形；采用带中断的独立式键盘作为命令的输入，每当按键时蜂鸣器响；配以LCD12864显示实现对带光码盘的直流电动机转速参数的测量、显示和控制。LMD18200驱动模块内部是H型驱动电路，驱动能力较强，完成电机正反转以及速度的控制。为优化直流电机的响应，采用PID反馈，实现闭环控制。(Graduation in the next, and that the requirements to design a DC motor control system. In the design, the use of the relatively new domestic microcontroller as a control circuit of STC12C5A60S2 entire control system core, because STC12C5A60S2 internal PCA module can generate PWM waveforms using a separate keyboard with interrupt input as a command, whenever the button When the buzzer sounds accompanied LCD12864 display realize the measurement of the optical encoder with DC motor speed parameters, display and control. LMD18200 internal drive module is H-drive circuit, driving ability, and the speed of completion of the motor reversing control. In order to optimize the response of DC motor, using PID feedback, closed loop control.)

白噪声发生器，利用白噪声发生器产生白噪声。白噪声发生器，可以调制幅值，频率，相位。白噪声发生器，是一款很好的发生器。(White noise generator, the use of white noise generator white noise. White noise generator, can be amplitude modulation, frequency, phase. White noise generator, is a very good generator.)

基于51单片机的电子密码锁设计，完整的文档。(Based on 51 single-chip electronic code lock design, complete documentation.)

大多数自行车速度表工作通过使用霍尔效应传感器固定在自行车前叉。磁铁是附加到前轮上的辐条之一,它将与霍尔效应开关一次革命的车轮。速度计监测传感器计数轮革命。如果知道车轮的直径,距离可以很容易地计算如果你知道有多少革命的车轮。此外,如果时间完成革命,平均速度也可以计算出来。 对于这个问题,您将编写一个程序来确定总距离(英里)和平均速度(英里每小时)考虑到车轮直径,革命的数量和总时间的旅行。你可以假定前轮从未离开地面,并没有下滑或打滑。(Most bicycle speedometers work by using a Hall Effect sensor fastened to the front fork of the bicycle. A magnet is attached to one of the spokes on the front wheel so that it will line up with the Hall Effect switch once per revolution of the wheel. The speedometer monitors the sensor to count wheel revolutions. If the diameter of the wheel is known, the distance traveled can be easily be calculated if you know how many revolutions the wheel has made. In addition, if the time it takes to complete the revolutions is known, the average speed can also be calculated. For this problem, you will write a program to determine the total distance traveled (in miles) and the average speed (in Miles Per Hour) given the wheel diameter, the number of revolutions and the total time of the trip. You can assume that the front wheel never leaves the ground, and there is no slipping or skidding.)