BCReader

说明：  双路输出控制器”具有信号输出时间设定、 输出信号占空比调整、 当前输出通道及时 间显示、系统工作参数存储、串口通讯及 LED 指示等功能。 “双路输出控制器”通过串口完 成信号输出时间设定功能；通过 EEPROM 完成系统工作参数存储功能；通过按键完成输出通 道切换、 输出信号占空比调整及停止信号输出功能； 系统硬件电路主要由 MCU 控制单元、独 立按键、 LCD 显示单元、 串口通讯单元、 EEPROM 数据存储单元和 LED 指示单元组成(Dual output controller has the signal output time setting, adjust the duty cycle of the output signal, the current output channel in time Between display, system operating parameters are stored, serial communications and LED indicator. Dual Output Controller through serial END A signal output time setting function complete system operating parameters via EEPROM memory function complete output pass through the key Channel switching, adjust the duty cycle of the output signal and the stop signal output function the system hardware circuit is mainly controlled by the MCU unit, alone Li buttons, LCD display unit, serial communication unit, EEPROM data storage unit and LED indication units)

数字温度计 DS18B20控制的数字温度计(Digital Thermometer DS18B20 digital thermometer control)

一个简单的小车单片机C语言控制，适合初学者(A simple car microcontroller C language control, suitable for beginners)

基于蓝牙协议栈BLE4.0的模块CC2541的ADC采集实验(Stack BLE4.0 module CC2541-based Bluetooth protocol ADC acquisition experiment)

由于太阳能充电系统多在户外，为了方便研究太阳能充电控制系统对蓄电池的充电情况，本文使用GPRS无线传输技术，设计了一套太阳能充电系统蓄电池的充电电压电流远程实时监测系统。系统的硬件部分由电压电流检测电路、单片机STC89C52RC、GPRS模块SIM300以及相应的外围电路构成，下位机软件由C语言编写并与硬件部分构成系统下位机部份，实现了对充电电压电流的信息采集以及数据的无线数传。上位机在LabVIEW2010环境下编写，具备友好的人机交互界面，实现了数据的远程接收、实时显示、数据库管理、报表生成和打印等功能。经过系统测试系统实现了对电压电流的远程监测。(As the solar charging system more outdoors, in order to facilitate the study of solar charge control system for charging the battery case, we use GPRS wireless transmission technology, we designed a solar charging system battery charge voltage and current remote monitoring system. The hardware part of the system by the voltage and current detecting circuit, microcontroller STC89C52RC, GPRS module SIM300 and corresponding peripheral circuits, lower computer software written in C language and hardware parts lower position machine part of the system, the realization of the charging voltage and current information collection and wireless data transmission of data. PC at LabVIEW2010 prepared environment, with friendly interactive interface, realize the remote receiving data, real-time display, management, report generation and printing. After the system test system enables remote monitoring of voltage and current.)

利用单片机作为芯片，利用点阵按钮通过继电器控制LED灯(Using single chip microcomputer as a chip, using bitmap button by relay control LED lights)

BlueCore4 Datasheet BC417143 ·APF有源滤波控制器程序，因为改代码 ·利用51单片机实现DS1302的驱动，以C ·利用STM8L实现诺基亚5110液晶的驱动 ·盛群单片机指令集:简体中文，PDF格 ·SHT11 程序，I2C总线方式。写I2C时 ·7寸彩屏 STM32的固件库3.5 FSMC驱动 ·一种伺服电机的PID控制算法，可以完 ·基于Atmega16单片机的机器人行走、 ·51单片机驱动2.6英寸触摸液晶屏幕， ·stm32 pwm 固件库 大连理工大学 信 ·无线传感网络基础 wireless sensor ·LPC11u14芯片的系统时钟驱动

一个简单的定时器定时0.5s和1s程序，指在教导新手如何使用定时器(A simple timer timer 0.5s and 1s procedures, means to teach novices how to use the timer)

本程序是TI的32位单片机LM3S9D96官方开发板上、基于IAR平台的，用C语言编写的的一个设计AD、液晶显示、串口打印的完整工程文件。已经调通。原创的程序。对于掌握LM3S些列单片机的高级功能很有用。(This program is TI' s 32 the microcontroller LM3S9D96 official development board, IAR platform, written in C language design the AD LCD, serial print complete engineering documents. Has been transferred Qualcomm. Original program. Useful advanced features master LM3S these columns microcontroller.)

51单片机控制16乘以16点阵，可以显示汉字等(51 single chip control 16 times the 16 dot matrix, you can display Chinese characters, etc.)