ENC28J60DEMO

Infi-90读写测试，在安装有COPOSER的计算机上可以运行，采集ABB DCS的控制逻辑块上的数据。(Infi- 90, speaking, reading and writing test, the installation of COPOSER can run on a computer, the data on the acquisition of ABB DCS control logic block.)

基于PSCAD/EMTDC的感应电动机负荷模型对电压恢复的影响。(Influence PSCAD/EMTDC induction motor load model based on voltage recovery.)

利用51单片机做电阻测量仪，实现按键设置阻值自动报警提示(The use of 51 single-chip resistance measuring instrument to achieve automatic alarm button to set the resistance)

本方案是基于富士通高可靠性单片机开发的锂电池电动螺丝刀，采用直流无刷电机作为核心，配合方波驱动以及闭环控制技术，实现电动工具的可靠运行。 技术参数 1）采用日本富士通MCU，性能稳定，抗干扰强，高可靠性； 2）直流18V输入（可兼容不同锂电池10V—36V）； 3）三相霍尔直流无刷电机驱动，转速高达25000转/分； 4）采用德国英飞凌高性能MOS/IGBT，驱动功率高达800W； 5）高亮LED照明，工作时点亮，不工作时自动熄灭； 6）采用智能控制技术实现待机（不工作时）功耗为 0 消耗； 7）通过软件实现软启动，启动时间可调整，瞬间（1S）达最高速； 8）具有过流保护、堵转保护、过压欠压保护； 9）带速度设置按键、正反转按键、调速开关； (The program is based on the Fujitsu MCU development of high reliability lithium battery electric screwdriver, brushless DC motor as the core, with the square wave drive and closed-loop control technology, power tools for reliable operation.)

使用VB与PIC采集,采用软件中断方式，使用研华1710集成卡。(Using VB with PIC acquisition, the software interrupt, use the the Advantech 1710 integrated card.)

这是单片机的安装源程序，这是第一次上传的单片机资料，希望能对大家有用(This is a single chip installation source, this is the first single chip data upload, hope it' ll be useful)

示波器的程序内涵 程序 文本 模拟 仿真的 (Program connotation oscilloscope simulation program text of)

MSP430F5529驱动DHT11,并用带字库的JLX12864显示(MSP430F5529 driver DHT11, and use the font JLX12864 display)

绿灯亮时，准许车辆通行，黄灯闪烁时，已越过停止线的车辆可以继续通行；没有通过的应该减速慢行到停车线前停止并等待，红灯亮时，禁止车辆通行。给行人看的叫人行横道灯，通常指由红、绿（绿为蓝绿）二种颜色灯组成用来指挥交通通行的信号灯，红灯停，绿灯行。(When the green light is on, the vehicle is allowed to pass. When the yellow light is flashing, the vehicles that have crossed the stop line can continue to pass.You should slow down to stop and wait at the stop line. No traffic is allowed when the red light is on.Pedestrian crossing lights for pedestrians, usually denoted by red, green (green, blue, green), two color lamps used to direct traffic signals, stop at red lights and green.)

编写的飞思卡尔的sd卡读写程序，可以完成对sd卡的扇区读写，效率高，执行速度快(Writing the freescale sd card reading and writing program, can complete the sd card to the sector, speaking, reading and writing, high efficiency, the execution speed)