MATLAB-and-51-

一款电厂巡检软件，很简单的C++处理程序，适合初学者使用，C++(A plant inspection software, very simple C++ handler for beginners, C++)

tms320F28335是一款新的dsp芯片，svpwm算法的实现和以前的2812等有点不同，现在将我写的分享给大家，已经调试过了，晶振是20MHz。28335的svpwm的实现。(tms320F28335 is a new dsp chip, svpwm algorithm implementation and the previous 2812 and so a little bit different, now I write for everyone to share, debugging, and the crystal is 20MHz. 28335 svpwm implementation.)

51单片机静态数码管显示51单片机静态数码管显示(sfasdasdasd )

1.44寸显示屏显示资料，可显示汉字，图片，彩色图片，带取模软件(1.44-inch display screen display data, can display Chinese characters, pictures, color pictures, with the module software)

Pocket 2003 Imager_SDK_14.12.20086 for software engineereing.

单片机键盘扫描程序 微处理器课程设计 八位抢答器(SCM keyboard scanning procedures microprocessor eight Responder Course Design)

滤波器广泛应用于数字信号处理、通信、自动控制领域,但设计可变宽频带有源滤波器则比较困难。利用单片机控制参数可编程的双二阶通用开关电容有源滤波器,精确设置有源滤波器的中心频率f，品质因数Q及有源滤波器的工作方式。本系统主要分为两个部分:即程控滤波器和程控放大器。程控放大器电压增益为40dB，通过单片机控制DA进行分压，可精确实现要求的10dB步进，误差小于0.5 ，通带为100Hz-500KHz，输入电压峰－峰值范围为10mV，在输入范围内无明显失真。由MAX264为核心的滤波器，可设置为高通、低通滤波器。通过单片机直接给出控制频率，使-3dB截止频率在1KHz-20KHz内可调，步进1KHz，误差小于1 。整个系统以52单片机为控制核心，电路简单，性能稳定，且具有较高精度，滤波参数调节通过单片机控制，较为方便。(Filters are widely used in digital signal processing, communications, automatic control area, but the design variable wideband active filter is more difficult. Control parameters using single-chip programmable universal switched-capacitor biquad active filter, active filter accurately set the center frequency f, quality factor Q and the active filter works. The system is mainly divided into two parts: the program-controlled filters and programmable amplifiers. Programmable amplifier voltage gain of 40dB, the DA through the partial pressure of single-chip control, can accurately achieve the required 10dB step, the error is less than 0.5 , passband to 100Hz-500KHz, input voltage peak- the range of 10mV, the input range no significant distortion. By the MAX264 as the core of filter can be set to high pass, low pass filter. Given directly by the microcontroller controls the frequency, the-3dB cutoff frequency at 1KHz-20KHz adjustable, step 1KHz, error is less than 1 . The entire system for)

stm8单片机实现了控制bldc轮毂电机的控制，用了6个mos管，采用六部控制，里面有 pcb sch 和程序，可以用此资料改装成电动自平衡独轮车(Stm8 microcontroller realized control BLDC hub motor control, with 6 mos tube, using six control with Sch and PCB program, this information is converted into electric self balancing unicycle)

配电网零序电流故障定位方法在PSCAD中的模型搭建，可以调整故障类型和短路电阻等进行故障模拟(The fault location method of zero sequence current in distribution network is built in PSCAD, which can adjust the fault type and short circuit resistance. )

本程序是用51单片机的PS2鼠标驱动程序(This procedure is used 51 single PS2 mouse driver)