登录
首页 » matlab » DWT_chain.m

DWT_chain.m

于 2011-12-30 发布 文件大小:2KB
0 211
下载积分: 1 下载次数: 5

代码说明:

  It wil perform DWT on a given signal using Chain process

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • pll0
    搭建pll电路,主要包括鉴相器,低通滤波器,压控振荡器,包括个部分的输出信号(Pll circuit structures, including phase detector, low pass filter, VCO, including a part of the output signal)
    2011-05-11 12:47:51下载
    积分:1
  • area_of_zhihui
    自己编的,实验数据中滞回曲线的面积计算,采用MATLAB编写。(calculate the experimental data hysteresis curve area )
    2021-04-21 22:08:49下载
    积分:1
  • jiasududaoshu
    MATLAB绘制汽车发动机加速度倒数曲线图(jia su du dao shu )
    2012-05-29 16:25:55下载
    积分:1
  • ex10
    Qpsk调制的基带数字通信系统通过awgn信道后的误码率(Qpsk modulated baseband digital communication system BER after channel through awgn)
    2014-10-22 19:19:01下载
    积分:1
  • Lempel_Ziv_program
    Lempel_Ziv信源编解码 含测试数据(Lempel_Ziv_Coder/Decoder test_data included)
    2012-04-02 11:05:45下载
    积分:1
  • toolbox_fast_marching
    The method mainly consists in considering a reference normal ECG segment and input ECG (unknown behavior) segment. Each segment of the input ECG T is compared to the reference segment using SEA. The SEA method outputs a measure in the range [0..1] in terms of the correlation factor that reflects the degree of similarity between the reference and the segment under analysis. Based on this measure, the whole segment is classified as normal or abnormal. A user specified threshold value on the correlation factor c is used for decision
    2011-11-10 13:11:39下载
    积分:1
  • MIMO
    BER SNR plot in rayleigh channel with maximal ratio combining technique for MIMO
    2010-10-08 14:42:32下载
    积分:1
  • WGCCM_three_link_walker_example
    说明:  基于matlab的双足机器人零动力学控制及其仿真,包括动力学及控制模块(Matlab biped robot based on the zero-dynamics control and simulation, including the dynamics and control module)
    2009-07-28 17:18:06下载
    积分:1
  • lle
    局部线性嵌入算法,由laurance等人于2000年science上发表,广泛应用于图像处理模式识别等领域,是一种流形学习算法。(the algorithm of locally linear embedding)
    2012-03-27 13:50:51下载
    积分:1
  • P_Controlv1.0
    说明:  用MATLAB实现的不合格品率P控制图的绘制,只要将数据导入data.txt文件,然后在MATLAB中运行main.m文件即可打开绘图界面。(注意:路径要设置好)(the failure rate of P Commodities Control Map, as long as the data into data.txt documents, then in MATLAB run main.m document can be open graphics interface. (Note : To set a good path))
    2006-04-16 12:07:55下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载