y

主要用于扩展频谱脉冲幅度调制当中波形的产生(Mainly used for spread spectrum pulse amplitude modulation waveforms which have)

自己编写多点采集数据处理程序，用于数值仿真多点采集，很好得到一个平均曲线，非常好用，用COMSOL仿真后处理，读CSV文件格式(Write your own multi-acquisition data processing program for the numerical simulation of multi-point acquisition, good to get an average curve, very easy to use COMSOL simulation post-processing, read the CSV file format )

交流伺服系统中的死区效应分析与补偿分析了逆变器的死区效应产生的原因及其对交流伺服系统控制性能产生的影响,指出死区补偿的关键 在于电流相位的获取,为了克服实际系统中电流零点的模糊性,提出了一种基于两相静止坐标系下的前馈死 区补偿方法. 该方法通过对三相输出电流一个周期内补偿电压进行傅里叶变换,发现仅需补偿1 ,5 ,7 次谐波 分量即可消除死区效应. 仿真和试验结果验证了这种方法的正确性和可行性.(AC servo system analysis and compensation of dead time effect of the inverter dead time effect causes the impact of the control performance of the AC servo system, and pointed out that the dead time compensation, the key lies in the current phase of the acquisition, in order to overcome the practical zero of the current ambiguity of the system is proposed based on the two-phase stationary coordinate system under the feedforward dead-time compensation method. by the offset voltage of the three-phase output current cycle Fourier transform is found only compensation 1, 5, 7 harmonic components to eliminate the dead time effect. simulation and experimental results verify the correctness and feasibility of this approach.)

丁星《MATLAB杆系结构分析源代码》 随书第二章源码： 1.结点位移自动编码 2.单元刚度矩阵计算与结构刚度矩阵集成 3.单元等效载荷计算与结构载荷矩阵集成 4.单元坐标系与结构坐标系转换 5.单元杆端位移和内力计算 6.单元截面内力和位移计算 7.单元机结构内力图和位移图绘制 8.支座位移计算 9.考虑温度作用的平面刚架静力分析 (Matlab Code for Statics Analysis of Plane Frame)

1、本程序用于仿真里德-穆勒（Reed-Muller）码在AWGN信道中的性能，调制采用bpsk 2、理论请参见《差错控制编码》（第二版），Shu Lin（美）编，晏坚等（译）一书P70-75.且仿真结果与书中图4-2完全一致 3、BPSK_AWGN_RM_Code.m为主程序，点击运行即可 4、The_creation_of_RM_code.m和RM_Decode.m分别为RM码的编、译码程序，而Majority_logic_decision.m用于译码中的大数判决，combine_dunction.m用于计算组合数。(1, the procedure for the simulation Reed- Muller (Reed-Muller) codes in AWGN channel performance, modulation using bpsk 2, theory, see " Error Control Coding" (second edition), Shu Lin (America) series , Yan Jian, etc. (translated) book P70-75., and the simulation results consistent with the book Figure 4-2 3, BPSK_AWGN_RM_Code.m-based program, click Run to 4, The_creation_of_RM_code.m and RM_Decode.m were RM compiled code decoding process, and in large numbers for decoding Majority_logic_decision.m judgment, combine_dunction.m used to calculate the number of combinations.)

Genetic algorithm all you need

matlab for cosine_modulated_gaussian

合成孔径雷达成像的三个经典算法matlab仿真。包括RD算法，Chirp Scaling算法，wK算法。程序正确，注释清晰。(Synthetic aperture radar imaging of three classical algorithm matlab simulation. Including RD algorithms, Chirp Scaling Algorithm, wK algorithm. Program correctly, clear notes.)

这是一个关于fiber tracking的源程序(This is a source of fiber tracking)

matlab车牌识别源码，完整的编译通过的程序和测试图片哦(matlab ticket recognition source code)