kalmantargettraching

自定义函数画图软件，软件的函数输入部分分为4部分，针对的是4个分段函数，当然也可以扩展为5段，六段，如果你的函数不用分段，那就只用在第一个edit里面写下你的函数表达式即可，同时要在后面写出x的范围，和cftool里面的custom equation一样，只能用matlab语法规范的函数表达式，即你不要写2x而是2*x，不要把我们的数学表达式和matlab表达式搞混淆了。从gif可以看出，在第一个edit输入不同的函数，有多项式函数，指数函数，三角函数，对数函数，axes都能有正确的图形，另外用其他edit配合，画出分段函数图像。因此，这可软件无论你是单个函数还是分段函数（4段以内）均可正确画出，当然还配合有grid选项，如果想保持画出的图形，无需QQ截屏，直接点保存键，将它以jpg的格式，存入到你想要存的文件夹里面。要想查对应点的函数值时，只用在edit里面输入x值，按回车就可以得到，注意x值是在范围之内的，支持结果累积，最终将以一个表格的形式显示出来，如果要想画新的图形，点击清空按键即可。(Drawing software-defined functions, the software function of the input part is divided into 4 parts, for the four sub-functions, of course, can also be extended to 5, Liu Duan, if you do not have sub-function, then only the first an edit which you can write your function expression, while the range in the back to write x, and cftool inside the custom equation, can only function with matlab syntax specification expression, but that you do not write 2x 2* x, not to our matlab mathematical expressions and expressions confused. It can be seen from the gif, in the first edit enter a different function, there polynomial functions, exponential functions, trigonometric functions, logarithmic functions, axes can have the right graphics, the other with the use of other edit, draw piecewise function image. Therefore, it can be software or whether you are single function piecewise functions (4 or less) can be correctly drawn, of course, with a grid option, if you want to keep drawing the graphics,)

这个是机械领域的二级展开圆柱斜齿减速器 设计的一些计算程序 自动化不高 要根据情况 改一些数据 但程序里有详细的说明 高手可以把它用GUI实现了(This is the area of secondary mechanical start helical gear reducer design automation of some of the computer program does not change according to the situation Gaoyao some data but the program in detail as master, it can be achieved with a GUI)

电磁场仿真,有限长通电螺线管的仿真程序，利用网格计算实验效果好(Electromagnetic field simulation, finite-length solenoid power simulation program, the use of grid computing experiments good results)

基于脉冲反射法定位电缆故障的M128代码,组合采样法对固定波形数据采样提高采样率。(Based on the pulse reflection method to locate cable faults M128 code, fixed combination waveform sampling data sampling to increase the sampling rate.)

PQ分解法求网络潮流，超详细的注解，可以仔细分析此程序，然后学着自己编写(PQ decomposition method the network trend, ultra-detailed annotations can carefully analyze this program, and then learn to write their own)

一个对应于C5.0的DEMO程序(a C5.0 corresponding to the procedures DEMO)

极好的有限元结构动力学分析算例，为初学者带来福音(good example for dynamic analysis)

基于EM算法的混合COPULA（Frank、Gumbel和clayton）(EM algorithm based on hybrid COPULA (Frank, Gumbel and clayton))

说明：  使用ADI方法解偏微分方程（二微加热器方程）(ADI method for the use of partial differential equations (2 micro-heater equation))

Volterra 级数，用于非线性建模，其中核需要自己确定，还有记忆长度(Volterra series for nonlinear modeling, in which the core needs to set itself, as well as memory length)