TLS3001(2012-11-10)

说明：  STC8G中文数据手册，包含封装，引脚功能。 包含各种功能的测试代码(Stc8g Chinese data manual, including package, pin function. Contains test code for various functions)

说明：  卡尔曼滤波-很不错，使用于姿态校正，使用陀螺仪和加速度计来进行计算(Kalman filter- a very good posture correction used, the use of gyroscopes and accelerometers to calculate)

说明：  STM32F1示波器基于STM32F1的一个简单的示波器，最大支持3.3v的电压，P1口作为输入。(Stm32f1 oscilloscopeA simple oscilloscope based on STM32F, with a maximum voltage of 3.3V and a P1 port as input.)

c8051f020的24c02程序，经测试验证可以使用。(c8051f020 of 24c02 procedures, verified by testing can be used.)

静态存储体设计 包含设计步骤， 原理图 设计心得等(Static memory bank design consists of design steps, such as schematic design experience)

用MSP430的比较器功能实现电阻的测量(Comparison with MSP430 function to achieve the measurement of resistance)

WSN的GAF算法程序针对无线传感器网络节点部署密集的特点，提出了 GAF 算法。在 GAF 算法中，根据节点的地理位置信息和节点的无线电发射半径（radio range），传 感器网络部署区域被划分为虚拟单元格（virtual gird）。根据自己的物理位置信 息，各个节点被划入到自己的单元格中。各个节点的物理位置信息可以由 GPS 或 其它定位系统得到。 (GAF algorithm of WSN deployment intensive features for wireless sensor network node, proposed GAF ​ ​ algorithm. In GAF algorithm, the radius of the radio transmitting node and the node' s location information (radio range), the sensor network deployment area is divided into a virtual cell (virtual gird). According to their physical location information, each node is classified into its own cell. The physical position information of each node can be obtained by the GPS or other positioning systems.)

8051驱动ht1622液晶驱动器的程序(8051 driver ht1622 LCD driver program)

It s amxmodx base. Very usefull administration tool for game servers like Counter-Strike

硬件资源: 1,DS0(连接在PA8)，DS1(连接在PD2上) 2,串口1(波特率:115200,PA9/PA10连接在板载USB转串口芯片CH340上面) 3,ALIENTEK 2.8/3.5/4.3寸LCD模块(仅支持MCU屏) 4,按键KEY0(PC5)/KEY1(PA15)/KEY_UP(PA0,也称之为WK_UP) 实验现象: 通过按键KEY_UP可以控制定时器AutoReloadTimer_Handle的开启，这个是 周期定时器，一旦开启就会不断的运行，直到按下KEY1将其关闭。按下KEY0 可以打开定时器OneShotTimer_Handle，这是个单次定时器，只会运行一次， 运行周期到了以后就会停止运行，除非按下按键KEY0将其再次开启。(Hardware resources: 1, DS0 (connected to PA8), DS1 (connected to PD2) 2. Serial port 1 (baud rate: 115200, PA9/PA10 connected on board USB to serial chip CH340) 3, ALIENTEK 2.8/3.5/4.3 inch LCD module (only supporting MCU screen) 4. Keyboard KEY0 (PC5)/KEY1 (PA15)/KEY_UP (PA0, also known as WK_UP) Experimental phenomena: The timer AutoReloadTimer_Handle can be turned on by keying KEY_UP. This is The periodic timer will run continuously once it is turned on until KEY1 is pressed to turn it off. Press KEY0 You can turn on the timer OneShotTimer_Handle, which is a single timer and only runs once. The run cycle will stop after that unless KEY0 is pressed to turn it on again.)