登录
首页 » matlab » MATLAB

MATLAB

于 2020-07-01 发布 文件大小:10KB
0 241
下载积分: 1 下载次数: 536

代码说明:

  matlab通过串口采集心电的GUI程序(matlab serial collection through the GUI ECG procedures)

文件列表:

seril2.fig
seril2.m

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • C8051_TCP
    基于CP2200的TCP/IP驱动程序,是嵌入式网络连接的最简单方案(The CP2200-based TCP/IP drivers, embedded network connectivity is the most simple program)
    2008-02-25 14:59:35下载
    积分:1
  • buzzer
    应用51单片机写的蜂鸣器的祝福歌,里面有详细的代码(51 microcontroller blessing song written by buzzer)
    2013-08-04 20:23:56下载
    积分:1
  • avr M128 & proteus
    说明:  这个是M128单片机的一些程序和proteus的例程(this is somet about danpianji)
    2019-04-11 17:00:18下载
    积分:1
  • TRAMS-arduino
    3D打印TMC5130驱动程序,修正了原版的错程问题(TMC5130 river for 3d printer, debug missing step problem.)
    2017-08-08 10:13:44下载
    积分:1
  • STM32蓝牙收发例程
    通用STM32开发板下,蓝牙收发功能的实现(Bluetooth Transceiver and Receiver Function under STM32)
    2020-11-13 16:19:42下载
    积分:1
  • 32测距(OLED显示)
    基于stm32f103zet6单片机的超声波测距(Ultrasonic ranging based on stm32f103zet6 single chip computer)
    2020-06-17 20:40:04下载
    积分:1
  • DS18B20_LCD1602_C51
    读取DS18B20进行温度测量以后的结果并在1602液晶上显示。 基于DS18B20的温度控制器。温度控制范围在20~30℃,当温度大于30度时,停止加热,小风扇通电开始降温,绿灯亮。温度低于20度时,小风扇停止通电,开始加热。红灯亮。全过程有LCD数字温度显示。(Read DS18B20 temperature measurement after the results of the 1602 LCD display. Based on DS18B20 temperature controller. Temperature control range of 20 to 30 ℃, when the temperature is greater than 30 degrees, stop heating, small fan is energized to start cooling the green light. When the temperature is below 20 degrees, a small fan is stopped is energized, the heating is started. Red light. The whole process of LCD digital temperature display.)
    2013-03-08 10:13:36下载
    积分:1
  • 31-(德飞莱)尼莫M3S-摄像头实验(OV7670_OV7725)
    串口调试助手,可显示波形,图像GPS定位,智能车助手(Serial debugging assistant, waveform display, image GPS positioning, intelligent car assistant)
    2020-06-19 02:00:01下载
    积分:1
  • Key
    msp430f149按键程序,非常完整,带中断,输入,输出(msp430f149 key procedures)
    2014-06-13 15:06:31下载
    积分:1
  • 采用STM32单片机制作的CAN双机通信程序 dual-CAN-communicate
    采用STM32单片机制作的CAN双机通信程序,附有说明文档(STM32 MCU CAN produced using dual machine communication program, with documentation )
    2013-09-02 15:34:05下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载