read-ssdt

基于STM32F4的示波器的源代码，内部含有ucos-ii操作系统。(STM32F4 based oscilloscope source code contains an internal ucos-ii operating system.)

$regfile = M8DEF.dat internal crystal 8000000 Config Lcdpin = Pin , Db4 = Portc.1 , Db5 = Portc.2 , Db6 = Portc.3 , Db7 = _ Portc.4 , E = Portd.2 , Rs = Portd.3 Config Lcd = 16 * 2 Config Timer1 = Counter , Edge = Rising Ddrb.1 = 0 : Portb.1 = 1 PULL UP RESISTOR ACTIVATED Config Timer0 = Timer , Prescale = 1024 Enable Counter1 Enable Interrupts Enable Timer0 Enable Timer1 On Ovf1 Pulsecount On Ovf0 Ovf0occures Dim A As Long , I As Long , B As Byte B = 0 Cls Start Timer0 Do Loop End end program Ovf0occures: Incr I If I > 30 Then Stop Timer0 Cls : Home A = B * 65536 A = A + Counter1 Lcd FREQ IS : A HZ B = 0 I = 0 : Counter1 = 0 Start Timer0 End If Return Pulsecount: Incr B Counter1 = 0 Return

TI公司的ADS1299是8路低噪音同时取样的24位delta-sigma ADC,并内置了可编程增益放大器(PGA),基准电压和振荡器,集成了脑电图(EEG)所需的通用特性.器件具有非常低的输入参考噪音:1.0 μVPP (70-Hz BW),没路的功耗5mW,输入偏置电流300pA,数据速率250SPS到16kSPS,C1.0 μVPP (70-Hz BW),CMMR为-110dB,可编程增益为1, 2, 4, 6, 8, 12或24,单极或双极电源工作,主要用在医疗仪器如EEG和ECG,听觉诱发电位(EAP),脑电双频谱指数(BIS),睡眠研究监测等,高精度多路信号采集.(The ADS1299 is a low-noise, multichannel, simultaneous-sampling, 24-bit, delta-sigma (ΔΣ) analog-to-digital converter (ADC) with a built-in programmable gain amplifier (PGA), internal reference, and an onboard oscillator. The ADS1299 incorporates all commonly-required features for electroencephalogram (EEG) applications.)

isight与adams、MATLAB、adaqus等集成源程序(isight and adams, MATLAB, abaqus and other integrated source)

单片机串口通信的应用，通过串口，我们的个人电脑和单片机系统进行通信。 个人电脑作为上位机，向下位机单片机系统发送十六进制或者ASCLL码，单片机 系统接收后，用LED显示接收到的数据和向上位机发回原样数据。(Single-chip serial communication applications, through the serial port, our personal computers and SCM systems to communicate. PC as a PC, send down bit microcontroller system or ASCLL hexadecimal code, after receiving the SCM system with LED display received data and sent back up crew as data.)

说明：  usb控制下位机led 灯的点亮,哦2混排博大精深进 .(jhsofgj k skdfgmdkf m k pkd fkgfpok fgk dpo )

SSD6实验，该实验练习指导如何分析测量程序的性能。这个实验完成后，你应该能够  理解如何测量程序的运行时间、  调整你的计划，以更快的知道的重要性(This laboratory exercises guide you how to measure the program’s performance using profiling. On completion of this laboratory, you should be able to  Understand how to measure the program’s running time  Be aware the importance of tuning your program to be faster)

此程序可实现长度为8位，周期为255的m序列，此序列可当做伪随机信号发生器，模拟信道噪声。(This procedure can achieve the length of 8 bits, the m sequence of 255 cycles, the sequence can be used as a pseudorandom signal generator, analog channel noise.)

此程序为毕业设计之防火防盗报警器具有MQ2烟雾报警，DS18B20温度报警，红外传感器感应人体红外，超声波感应人得进入，加上1602液晶显示等功能，同时具有蜂鸣器及LED报警(This procedure for the graduation of the fire alarm system design has MQ2 smoke alarm, DS18B20 temperature alarm, human infrared sensor infrared sensor, ultrasonic sensor people allowed to enter, plus 1602 LCD function, but also has a buzzer and LED alarm)

基于 AVR 单片机的水温自动控制系统 摘要: 本系统以 ATMEGA16 单片机作为系统的检测和控制核心，采用温度传感器 AD590实现0—100℃温度范围内的实时温度采集，通过双向可控硅 BT136 控制电热杯对系统进行加热，利用继电器控制半导体制冷片对系统进行散热。通过一线键盘实现对任意温度值进行设定并对模糊 PID 参数的调整，液晶 LCD1602 实时更新显示当前温度测量值与键盘设定温度值。利用模糊 PID 算法，通过调功法对水温系统进行控制,实现在 0—100℃范围内任意设定温度值，静态误差小于±0.5℃。 关键词： AVR 单片机 水温自动控制 模糊 PID 算法 (AVR Microcontroller Based Temperature Control System Abstract: This system ATMEGA16 microcontroller as the core monitoring and control system using the temperature sensor AD590 0-100 ℃ temperature range to achieve real-time temperature acquisition, through triac BT136 control system for electric heating cup, using relay control system for semiconductor cooling heat tablet. Achieved through the keyboard line value for any temperature setting and adjustment of fuzzy PID parameters, real-time updates LCD1602 LCD displays the current temperature measurements and the keyboard set temperature. Fuzzy PID algorithm, the system transfer function method of temperature control, to achieve the 0-100 ℃ adjustable set temperature, the static error is less than ± 0.5 ℃. Keywords: AVR microcontroller water temperature control fuzzy PID algorithm )