MMWIR

本演示实现了主动轮廓模型由Kass等人提出。 要运行它的图形用户界面 1。基于MATLAB型引导提示。 2。关于“到现有的图形用户界面，点击” 3。选择在与本文件相同的目录snk.fig文件 4。按一下上方的绿色箭头启动图形界面 一旦GUI已经启动，您可以通过使用蛇 1。点击“新形象”，并加载输入图像。提供的样品图像。 2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。 3。只要你点击“过滤器”，头发会出现交叉，用他们和你左击鼠标，您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下，你应该单击对象周围的一切你想要的部分。最后一点，必须挑选使用右键单击，以阻止更多的积分为MATLAB的要求。 4。设置各种蛇参数（在能源方面的相对权重的蛇目标函数）或离开它们的默认值，然后按一下他们“迭代”按钮。蛇会出现和移动，因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al. To run it with GUI 1. Type guide on the matlab prompt. 2. Click on "Go to Existing GUI" 3. Select the snk.fig file in the same directory as this file 4. Click the green arrow at the top to launch the GUI Once the GUI has been launched, you can use snakes by 1. Click on "New Image" and load an input image. Samples image are provided. 2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image. 3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points. 4. Set the various snake paramete)

Hi i have attached facts controller

一个MATLAB的GUI界面编程实例，类似于一般的软件界面，开发环境MATLAB7.4（R2007b）(A MATLAB-GUI interface for programming examples, similar to the general software interface, development environment MATLAB7.4 (R2007b))

自己编写的程序，用jacobi方法来求解对称矩阵的特征值还有用OR算法以及反幂法来求解特征值。(I have written procedures, with jacobi method to solve the symmetric matrix eigenvalue algorithm have to use OR as well as anti-power-law to solve the eigenvalue.)

pll的仿真matlab中的simulink(pll matlab simulink)

ofdm调制方式识别的matlab仿真程序，即ofdm信号与单载波信号之间的识别，利用的是高阶累积量作为特征参数(Ofdm modulation mode recognition of matlab simulation program, that is, between ofdm signal with single carrier signal recognition, using the high-order cumulants as characteristic parameters)

多重分形去趋势交叉相关性分析DCCA,以及MF-DXA等程序代码，希望对大家有帮助(Multifractal cross correlation analysis of DCCA, and program code such as mm-dxa, hope to be helpful)

this application is used to search in data base to get some data with special specificaton

说明：  对含储能和风电的电力系统进行了可靠性评估，利用序贯蒙特卡洛法，把风储系统接入IEEE-RBTS系统来仿真，探讨了风电场、储能系统、储能容量和储能最大充放电功率对系统可靠性的具体影响。(This paper evaluates the reliability of the power system including energy storage and wind power. The sequential Monte Carlo method is used to connect the wind storage system to the ieee-rbts system for simulation. The specific effects of the wind farm, energy storage system, energy storage capacity and the maximum charge and discharge power of energy storage on the reliability of the system are discussed.)

LTE for UMTS - OFDMA and SC-FDMA Based Radio Access 关于随机接入很好的一本书籍是针对LTE系统的。(LTE for UMTS- OFDMA and SC-FDMA Based Radio Access on the random access good books for a LTE system.)