antColony

Power Steering: Brushless DC I or Switched-Reluctance?

主要包括图像的中值、均值去噪、非局部均值、分块局部去噪算法；还有均方误差和峰值信噪比评价、以及matlab基础学习资料如边缘检测、小波变化、灰度值转换等(Including image median, mean denoising, non-local means, block local denoising algorithm also mean square error and peak signal to noise ratio evaluation, and matlab based learning materials such as edge detection, wavelet transform, gray scale value conversion wait)

利用matlab演奏的生日快乐歌，别有一番风味，不妨一听(Using matlab played Happy Birthday, do not have a flavor, might one)

此仿真程序是目前论坛里面最完整的仿真源码，并且经本人调试运行，完全没有错误，有很高的研究价值。为各位搞仿真和做OFDM系统相关论文的研究生，而没有全面仿真程序的人提供本程序。此程序包含52个仿真模块，可以仿真出52个仿真图。(This simulation program is the forum inside the most complete source of emulation and debugging, as I run, there is no error, has high research value. For you to do engage in OFDM system simulation and related post-graduate theses, and no comprehensive simulation program provide the program. This program contains 52 simulation module can be a simulation simulation Figure 52.)

图像灰度变换的基本运算函数，对于其了解有很重要作用，这是老师代码(Image gray-scale transformation of the basic arithmetic function, for a very important role in their understanding, it is the teacher code)

图像处理基础算法源代码MATLAB集合，里面很多修改就可以用(Image Processing MATLAB based algorithm source code set, which can be used to modify many)

Compute fractal dimensions FDS and intercepts ICS of a 3D image IM using FFT and draw rose plots of FDS and ICS

采用GA对神经网络的权值与阀值进行优化，得到效果更好的网络(GA uses neural networks for weights and thresholds are optimized to get better network)

xwch_test.m是主测试文件；biaoji.mat存放滤波器系数；xiangweicha.m用FFT计算相位差。 仿真框架为： 1.标记信号和双音信号续接作为发送信号； 2.对双音中一个频率分量的相位做偏移，再经过一个低通滤波器（引入线性相位，模拟收发不能同步测量现象）后，作为收到的信号； 3.用一个检测信号对收发信号进行相关运算； 4.画出收发信号以及相关处理后的信号。找出相关信号的那个尖点，从而推算出收发双音信号0相位点； 5. 输入0相位点位置，计算相对相位差。(xwch_test.m is the main test file biaoji.mat store filter coefficients xiangweicha.m calculated using FFT phase difference. Simulation framework: 1. Mark signals and then as a two-tone signal continued to send signals 2. On a two-tone frequency components of the phase shift to do, and then through a low pass filter (the introduction of linear phase, simulation can not simultaneously send and receive measuring the phenomenon), the as received signal 3. using a detection signal of the transceiver signal correlation operation 4. draw send and receive signals and related processed signal. Correlated signal of the cusp, which calculate the two-tone signal transceiver 0 phase point 5. Enter 0 phase point position, calculate the relative phase difference.)

这个程序代码用于提取眼底图像的血管，包括去噪、边缘检测(The program code for extracting a blood vessel image of the fundus, including denoising, edge detection)