5PS2MOUSE1

该程序为初学者学习单片机时使用的60S倒计时程序，可将开程序用在proteus软件上进行仿真，我试过可行的~(The program for beginners to learn the use of single-chip microcomputer of the 60S countdown procedures, can be used in open procedures proteus simulation software, I tried to possible ~)

cc2530zigbee芯片英文资料，数据手册(cc2530zigbee chip information in English, Data Sheet)

代码说明： 需要建立汽车模型的朋友请看看吧！这么长了还短 垃圾网站 (Need to build car model friends look out! )

基于atmel studio 6，使用avr128单片机，实现超市导购机器人编程，直流电机结合颜色传感器实现自动巡线，5个舵机，3个自由度(Based on atmel studio 6, using avr128 microcontroller, to achieve the supermarket shopping guide robot programming, combined with the color sensor DC motor automatic transmission line, 5 servos, three degrees of freedom)

固高运动控制卡GE-400-PG随机光盘(GoogolTech GE-400-PG accompany CD)

这是一个为数不多的用C语言编写的PIC12C508的RGB灯的小型控制器，交流同步信号检测，七彩跳变+七彩渐变，做LED的朋友可以参考，程序可以直接使用的；(This is a small controller RGB lights a few written by C PIC12C508, AC synchronous signal detection, colorful jump+ colorful gradient, do LED friends can reference, the program can be used directly )

lexical analysis of text detail program...

STM32 SPI读写FM25CL64铁电存储器，程序为103RBT6单片机读写代码，包括SPI初始化、字节发送接收代码、FM25CL64读写代码(STM32 SPI read/write FM25CL64 ferroelectric memory, the application for 103 rbt6 microcontroller, speaking, reading and writing code, including the SPI initialization code byte code to send and receive FM25CL64, speaking, reading and writing )

PSCAD逆变器仿真模型 (PSCAD simulation model of inverter)

步进电机是将电脉冲信号转变为角位移或线位移的开环控制电机，是现代数字程序控制系统中的主要执行元件，应用极为广泛。。在非超载的情况下，电机的转速、停止的位置只取决于脉冲信号的频率和脉冲数，而不受负载变化的影响，当步进驱动器接收到一个脉冲信号，它就驱动步进电机按设定的方向转动一个固定的角度，称为“步距角”，它的旋转是以固定的角度一步一步运行的。可以通过控制脉冲个数来控制角位移量，从而达到准确定位的目的；同时可以通过控制脉冲频率来控制电机转动的速度和加速度，从而达到调速的目的。(Stepper motor is an open loop control motor which transforms electrical pulse signal into angular displacement or linear displacement. It is the main executive element in modern digital control system, and is widely applied. In the case of non overloaded, the motor speed and stop position depends only on the pulse frequency and pulse number, regardless of load changes, when the stepper driver receives a pulse signal, it drives stepper motor to set the direction of rotation of a fixed angle, called "step", it is the rotation of the fixed point of the operation step by step. We can control the angular displacement by controlling the number of pulses, so as to achieve the goal of accurate positioning. At the same time, we can control the speed and acceleration of motor rotation by controlling the pulse frequency, so as to achieve the purpose of speed regulation.)