JESD204B_character

药品恒温箱控制程序，定义了大量的宏，希望对你有帮助(asm soft )

没有使用ADS，是搭建在keil下的s3c2440裸机程序，实现TOUT0的PWM输出来控制舵机(No use ADS, is to build a bare-metal s3c2440 in keil procedures to achieve TOUT0 PWM output to control steering)

单片机红外遥控最全的资料，包含很多当前电视遥控专用芯片的解码方式，C语言和汇编语言编写的解码范例程序，看完了你就会了！(infrared remote control MCU most complete information, including many current television remote control decoder ASIC, C and Assembly Language prepared by the example of decoding procedures will be watching you!)

实现函数发生，基于51单片机的汇编语言，可以实现正弦波，方波，三角波，锯齿波，频率可调(Realization function generator, based on 51 single-chip assembly language, you can achieve sine, square, triangle, ramp, adjustable frequency)

基于msp430的DDS芯片ad9851的源码,(MSP430 Based on the DDS chip AD9851 source,)

基于PS2协议的鼠标进行位移测量，已经经过测试(The mouse displacement measurement based on PS2 protocol，It has been tested)

DGCL （An Efficient Density and Grid Based Clustering Algorithm for Large Spatial Database）的实现代码，费了很长时间才实现的(DGCL (An Efficient Density and Grid Based C. lustering Algorithm for Large Spatial Databas e) the realization of code, and a very long time to achieve the)

proteus仿真，以LPC2138芯片为核心生成PWM波，控制升压斩波电路（PWM），实现稳定的高电压输出。包含AD转换、串口通信。(proteus simulation. This design use PWM wave generated by LPC2138 to control boost circuit and realized a steady high voltage output. ADC and serial port communication are involved in the design.)

缺水报警器 硬件 1.主控板上有2个LED灯白色插座，连接2个LED插头 2.主控板上有一个缺水报警探头插座，连接缺水测试探头 3.主控板上有一个蜂鸣器 功能 1.上电后蜂鸣器鸣叫一声，进入工作状态 2.进入工作状态后，利用探头进行自动测试，若发现没有达到一定的水量（检测端口断开），便立刻进入报警状态，红LED闪（蓝灯灭），蜂鸣器鸣叫，LED灯和蜂鸣器的鸣叫频率均为2HZ。（蜂鸣器为4khz的压电式蜂鸣器） 3.或者将探头短接，也将视为有水，则蓝灯长亮（红灯灭，蜂鸣器不叫）。 (Water alarm hardware 1 master board has two LED lights white socket, connect two LED plug 2. The main control board has a water alarm probe socket, connect the test probe is water 3 main control panel a buzzer function 1 after power buzzer sound, into the working condition (2) to enter the work state, the use of automatic test probe, if it did not reach a certain amount of water (test port off), they immediately go into alarm state, the red LED flashes (blue light), buzzer, LED lights and buzzer frequency chirping are 2HZ. (Buzzer piezoelectric buzzer for the 4khz) 3, or short the probe will also be seen as water, the long bright blue light (red light off, the buzzer is not called).)

DC motor speed controller