mainMATLABfunction

波音727的数据和isar技术成像程序，希望对大家有帮助(Boeing 727 isar technical data and imaging procedures, we hope to help)

1、系统仅处于训练状态。训练序列为2cos(2π×f1×n/fs)， 干扰为sin(2π×f2×n/fs)；序列长度为100个样点。 其中n=0…99，f1=1kHz，f2=2kHz，fs=8kHz。 2、采用LMS算法，均衡器输入为训练序列加上干扰，均衡器阶数为21阶，步长因子β=0.01。 3、在Matlab中编写浮点LMS算法，绘制均衡器的输出波形，并与训练序列进行对比。 (1, the system only in the training status. The training sequence is 2cos (2πf1n/fs), interference sin (2πf2n/fs) sequence length of 100 samples. Where n = 0 ... 99, f1 = 1kHz, f2 = 2kHz, fs = 8kHz. 2, using LMS algorithm, the input to the equalizer training sequence plus interference equalizer order is 21 bands, step factor β = 0.01. 3, the preparation of the floating-point LMS algorithm in Matlab, draw the output waveform equalizer, and with the training sequence comparison.)

M=63 J=(M-1)/2 Wp=0.5*pi Ws=0.6*pi Np=100 Ns=100 weightp=1 weights=100 通带和阻带的加权系数 WpN=linspace(0,Wp,Np) WsN=linspace(Ws,pi-0.05,Ns) Wm=[WpN WsN] p=[ones(1,50),ones(1,50)/2] d=[p,zeros(1,Ns)] W=diag([weightp*ones(1,Np),weights*ones(1,Ns)]) C=cos(Wm*[0:J]) Q=diag(cos(Wm*0.5)) g=(W*Q*C)(W*d) g=g h=(g(J:-1:2)+g(J+1:-1:3))/4 h=[g(J+1)/4 h g(1)*0.5+g(2)/4] h=[h fliplr(h)] W=linspace(0,pi-0.1,512) H=freqz(h,1,W) plot(W/pi,20*log10(abs(H))) (filter design)

现代信号处理中谱估计在matlab中的使用，基于matlab GUI界面设计,合成孔径雷达（SAR)目标成像仿真，基于互功率谱的时延估计，多目标跟踪的粒子滤波器，基于分段非线性权重值的Pso算法。( Modern signal processing used in the spectral estimation in matlab, Based on matlab GUI interface design, Synthetic Aperture Radar (SAR) imaging simulation target, Based on the time delay estimation of power spectrum, Multi-target tracking particle filter, Based on piecewise nonlinear weight value Pso algorithm.)

MATLAB通信仿真及应用实例详解,希望对大家有用(Communication and application of MATLAB simulation examples of detailed, in the hope that useful to everybody)

说明：  现在手头有一个matlab程序，是关于如何改变坐标轴范围的。跟大家分享下！(change the range of the axis)

r tree generation in matlab is given

simulink了一个可以实现前馈和反馈控制的模型，两个拨钮选择前馈还是反馈控制。(make a modle that can simulink a feedback and feedword control system.)

If you have not registeredDF

平均标准偏差，一个计算用的Matlab小程序，希望大家喜欢(The average standard deviation, a calculation using a small Matlab program, I hope everyone likes)