cc2530-datasheet

STM8 源代码 STM8 programming language TMIR1 TMIR2 SPI IIC (STM8 programming language TMIR1 TMIR2 SPI IIC )

温湿度串口检测程序，实现对数据的读取和检测(Temperature and Humidity Serial Port Detection Program for Data Reading and Detection)

公交自动报站系统的设计，需要用到语音芯片，还有显示器，用单片机设计，protues进行仿真(Automatic stop system bus design, the need to use voice chip, as well as monitors, MCU design, protues simulation)

模数转换器AD0809例程，通过该例程可掌握AD0809的基本使用方法(AD0809 ADC routines, the routines can be mastered through the basics of using the AD0809)

ECG for msp430心电数据采样及LCD显示，官方样板程序。(ECG for msp430 )

双馈风电机组的PSCAD模型，是通用模型，有助于帮助解决双馈风电机组建模问题(PSCAD doubly-fed motor model)

基于单片机的一些基础应用 和硬件设计以及综合设计(89c51Integrated application hardware design)

IRMCK171的FOC控制无刷电机控制原理图 IR内部资料啊(Control of IRMCK171 FOC brushless motor control schematic IR internal data)

430与串口和定时器的详细例程，可在链接da或ad时调用(430 link da or ad with serial timer routine, call)

滤波器广泛应用于数字信号处理、通信、自动控制领域,但设计可变宽频带有源滤波器则比较困难。利用单片机控制参数可编程的双二阶通用开关电容有源滤波器,精确设置有源滤波器的中心频率f，品质因数Q及有源滤波器的工作方式。本系统主要分为两个部分:即程控滤波器和程控放大器。程控放大器电压增益为40dB，通过单片机控制DA进行分压，可精确实现要求的10dB步进，误差小于0.5 ，通带为100Hz-500KHz，输入电压峰－峰值范围为10mV，在输入范围内无明显失真。由MAX264为核心的滤波器，可设置为高通、低通滤波器。通过单片机直接给出控制频率，使-3dB截止频率在1KHz-20KHz内可调，步进1KHz，误差小于1 。整个系统以52单片机为控制核心，电路简单，性能稳定，且具有较高精度，滤波参数调节通过单片机控制，较为方便。(Filters are widely used in digital signal processing, communications, automatic control area, but the design variable wideband active filter is more difficult. Control parameters using single-chip programmable universal switched-capacitor biquad active filter, active filter accurately set the center frequency f, quality factor Q and the active filter works. The system is mainly divided into two parts: the program-controlled filters and programmable amplifiers. Programmable amplifier voltage gain of 40dB, the DA through the partial pressure of single-chip control, can accurately achieve the required 10dB step, the error is less than 0.5 , passband to 100Hz-500KHz, input voltage peak- the range of 10mV, the input range no significant distortion. By the MAX264 as the core of filter can be set to high pass, low pass filter. Given directly by the microcontroller controls the frequency, the-3dB cutoff frequency at 1KHz-20KHz adjustable, step 1KHz, error is less than 1 . The entire system for)