登录
首页 » matlab » lunwen

lunwen

于 2011-05-26 发布 文件大小:260KB
0 189
下载积分: 1 下载次数: 50

代码说明:

  用MATLAB实现一种快跳频通信系统毕业论文。Word版(Using MATLAB to achieve a fast frequency hopping communication system thesis. Word version)

文件列表:

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • exa120602_db53
    说明:  本程序利用提升方案实现db5/3小波滤波器,并用该小波进行图像的分解(This procedure used to enhance the program to achieve db5/3 wavelet filter, and use the wavelet decomposition for image)
    2011-04-06 20:11:56下载
    积分:1
  • shiyanyi
    matlab上机实验:系统响应及系统稳定性(System response and system stability )
    2012-05-14 14:59:38下载
    积分:1
  • baoluofenxi
    采用解调分析方法,从信号中提取调制信息,分析其强度和频次就可以判断研究对象(诸如机械零件)损伤的程度和部位。(Using the demodulation method, the modulation information is extracted from the signal, the strength and frequency analysis can determine the study (such as mechanical parts) and location of the degree of damage.)
    2013-09-30 04:08:32下载
    积分:1
  • TVAR_Lib
    是一个时变AR(Time Varying Autoregressive)模型的工具箱。(It is a toolbox for model of Time-Varying Autoregressive.)
    2020-10-20 20:57:24下载
    积分:1
  • T型三电平逆变器
    说明:  T型三电平控制PMSM仿真,用于永磁同步电机控制,逆变器 三相逆变器 适合 在matlab环境下运行(PMSM simulation of T-type three-level control for permanent magnet synchronous motor control. Inverter three-phase inverters are suitable for operation in MATLAB environment.)
    2021-04-11 11:38:57下载
    积分:1
  • visible_number
    读取星历观测文件GPS和北斗卫星的可见卫星数作为输出(read ephemeris observation file to give out GPS and Beidou visible satellite number)
    2015-03-12 20:53:32下载
    积分:1
  • Optimalreceptionofadditivewhite
    本设计主要对4PSK调制方式的信号,利用MATLAB的m文件进行最佳接收机的设计与仿真。对输入的叠加噪声的4PSK调制信号进行接收,利用相关解调器来实现信号解调,及最大似然准则来实现检测器。在相关解调器中,接收信号分别与基函数 和 相乘再积分。在检测器中,利用相位来判断输出,从而最终得到接收的数据。采用随机二进制数通过4PSK调制后叠加高斯白噪声再对设计的接收机进行测试,从测试的结果可看出,在信噪比大于-8dB时,误码率为0,说明该接收机较好的实现了抗噪声性能。(The design of the main 4PSK modulation mode of the signal, the use of MATLAB m file for the best receiver design and simulation. The 4PSK modulated signal of the input superimposed noise is received, and the demodulator is realized by the relevant demodulator, and the maximum likelihood criterion is used to realize the detector. In the associated demodulator, the received signal is multiplied by the basis function and multiplied by the basis function. In the detector, the output is judged by the phase, and finally the received data is obtained. Using the random binary number through 4PSK modulation after the superposition of white noise and then the design of the receiver to test the test results can be seen in the signal to noise ratio greater than-8dB, the bit error rate is 0, indicating that the receiver is better The realization of the anti-noise performance.)
    2020-10-24 00:07:22下载
    积分:1
  • Mathematical-modeling-(2)
    基于GUI界面的数学建模、图像处理、以及公式计算。(GUI based interface mathematical modeling, image processing, as well as the formula.)
    2012-09-15 00:13:30下载
    积分:1
  • SOD-Segment-based
    attached file contains matlab code
    2014-12-06 13:10:08下载
    积分:1
  • utility-function
    utility function 1234
    2011-11-24 13:11:11下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载