wsn-topology

MATLAB数值计算经典教程MATLAB numerical classic tutorial(MATLAB numerical classic tutorial MATLAB numerical classic tutorial)

说明：  常规的单载波调制技术在带宽有限的测井电缆上的低传输速率制约着成像测井技术的发展。在分析测井 电缆传输特性和 OFDM 技术原理的基础上 ,设计了一种基于 OFDM 技术的测井电缆高速数据传输系统 ,并介绍了 基于 OFDM 技术的测井电缆高速数据传输系统的参数设计和工作原理 ,给出了不同长度测井电缆上的测试结果。 电缆实测结果表明 ,在 7 000 m长的测井电缆上 ,基于OFDM 技术的测井电缆高速数据传输系统可获得900 kbit / s 以上的数据传输速率和低于 5E28 的误码率。当变压器的接入模式为 Mode2II时 ,系统最高的数据传输速率可达到 1. 1 Mbit/ s。(To solve t he low data t ransmission rate problem in t he conventional single car rier mod2 ulation met hod for logging cable and enhance t he data t ransmission rate , a new data t ransmission system with high data t ransmission rate for logging cable is propo sed , which is based on t he Or2 t hogonal Frequency Division Multiplexing (OFDM) technology. The working principle of OFDM modem and t he procedure of data t ransmission system are al so presented and lot s of test s are car2 ried out on logging cables with different lengt hs. It is verified that t he data t ransmission rate can reach 900 kbit/s on 7 000 meter s logging cable wit h bit er ror rate (BER) lower t han 5E28 , and t he maximum data t ransmission rate is 1. 1 Mbit/s under Mode2II of t he t ransformer .)

使用matlab产生混沌时间序列的源代码(use Matlab chaotic time series generated source code)

生成一个一定参数的原信号，并附加一个符合均匀分布的随机噪声，分别画出该信号经过均匀采样的频谱图以及经过非均匀采样的频谱和时域图(Generate a certain parameter of the original signal, and attach a line with uniformly distributed random noise were drawn through uniform sampling of the signal spectrum as well as through non-uniform sampling of the spectrum and time domain)

DSPAlgorithms:Algorithm Collections for Digital Signal Processing Applications using Matlab .i think it will help the coders

R语言实现的一个简单的AHP，层次分析的源码。(The code belonging to the data analysis of R language source code level analysis.)

matlab用于模拟程序化交易。双EMA交易系统，用于优化参数。(matlab for simulating program trading. Two-EMA trading system, used for parameter optimizing.)

该代码实现了以2为因子的图像升采样和降采样功能。 降采样包括使用平滑滤波器(with using the averaging filter)和不使用平滑滤波器(without using the averaging filter)两种方法。 升采样包括像素点直接复制(pixel replication method)和线性插值(bilinear interpolatoin method)两种方法。 降采样方法和升采样方法共有4种组合。程序运行后，给出了一个原始图片和四个结果图片。 图片1.原始图片。 图片2.平滑滤波器降采样&像素点直接复制升采样。 图片3.平滑滤波器降采样&线性插值升采样。 图片4.不使用平滑滤波器降采样&像素点直接复制升采样。 图片5.不使用平滑滤波器降采样&线性插值升采样。 (The code to achieve a 2-factor image upsampling and downsampling function. Down-sampling (with using the averaging filter) and do not use smoothing filter (without using the averaging filter) are two ways to use the smoothing filter. Upsampling including the pixels copied directly (pixel replication method) and linear interpolation (bilinear interpolatoin method) two methods. Down-sampling method and liters a total of four combinations of sampling methods. The program is running, it shows a picture of an original picture and four results. Picture 1 original picture. Photo 2. Smoothing filter downsampling & the pixel directly copied liter sample. Photo 3. Smoothing filter downsampling & the linear interpolation liter sampling. Picture 4. Smoothing filter down-sampling & the pixels directly copied liter sampling. Picture 5. Use smoothing filter down-sampling & the linear interpolation liter sampling.)

基于MATLAB的2PSK调制,模擬錯誤率(MATLAB-based 2PSK modulation, analog error rate)

matlab code for sensor nodes