MP3

说明：  看电子电路时序图如何看，这是个好方面，可以看看(Electronic circuit timing diagram to see how the look, this is a good side, you can see)

用共阴极数码管做的密码锁,可修改密码 ( this is a codelock )

51单片机的应用ad9850DDS数字信号源的C语言程序(51SCM ad9850 DDS SIGNAL GENERATOR )

本程序主要是对小车进行左转控制，有三种方法左轮抱死，右轮抱死，或者左轮后退右轮前进，三种方式进行左转(This procedure is mainly to control the car on the left, there are three ways, revolver, holding in death of the wheel lock, right or left back right wheel to go forward, three ways to turn left)

AVR ATmeg16单片机的串口通信,这个程序非常实用，发送采用查询方式，接收采用中短方式。(This pramer is very good，it can transmit your massage you press on the software of PC.Try it and like it.)

使用方法： 程序设置了ENC28J60的IP为192.168.0.15，模块通电后与电脑的网口用网线连接起来， 设置电脑的本地IP为192.168.0.**（**自定），网关为192.168.0.15,其他默认，配置 成功后便可以arp或ping模块。 打开浏览器，在地址里输入http://192.168.0.15/123456可打开开发板简单网页，页 面上通过按键来控制开发板LED的亮灭。(Use: setup the ENC28J60 of IP to 192.168.0.15, the module is powered on the computer' s Ethernet port using a cable connection up to set the computer' s local IP 192.168.0.** (** Custom), the gateway 192.168.0.15, default configuration is successful, it will make arp or ping module. Open the browser, enter the address http://192.168.0.15/123456 to open the development board simple web pages, and page keys to control the development board LED light off.)

利用 USB2I2C开发板和软件实现了对CMOS图像传感器的在线调试。该系统运行稳定，体积小，外围电路简单，可灵活应用于多种CMOS图像传感器在线调试的场合以进行图像质量调整。本系统在调试过程中能生成调试log文件和寄存器配置文件。调试log文件记录调试过程中寄存器更改过程，可方便追踪、查看调试过程；寄存器配置文件保存最终调试结果，方便用户进一步的应用。(Use USB2I2C development board and software realization of the CMOS image sensor circuit debugging. The system is stable, small, simple external circuit can be flexibly applied to a variety of CMOS image sensors in-circuit debugger occasion for image quality adjustment. The system can generate in the debugging process debugging log file and registers the configuration file. Debug log file records the process of debugging registers the change process, can be easily tracked, view the debugging process register configuration file to save the final result debugging, user-friendly application further.)

AD0809的功能启动，描述了如何启动AD0809的数模转换功能，并且在旁边加油注释(The AD0809 s function is activated, and describes how to start the AD0809 digital to analog conversion function, and next to the fuel comment)

串口下发至数码管显示，本程序已通过编译，可直接使用(Serial issued to the digital display, the program has been compiled, can be used directly)

使用Atmega16单片机和Att7022计量芯片检测有功功率，有详细的校表过程，在此程序基础上可已开发更多功能(Att7022 Atmega16 measured using microarray microcontroller and active, detailed calibration process, this procedure can be developed on the basis of more features)