ggd

本作品可实现如下功能： 1. 显示年、月、日、星期等日期项 2. 显示时、分、秒等时间项 3. 测量并显示温度 4. 秒表（含开始，暂停，继续，复位等） 5. 闹钟（含开关，时间设定，是否启用的标志等，精确到秒） 6. 时间和日期的校正（加减均可） (The works can achieve the following functions: 1 year, month, date, day of the week, the date of entry. Displayed, minutes, seconds time of 3 to measure and display the temperature. The stopwatch (including start, pause, resume, reset etc. ) 5 alarm (including switch, time set, the flag is enabled, accurate to seconds) the time and date of the correction (addition and subtraction can be))

超声波避障小车c程序 数码管显示程序(Ultrasonic obstacle avoidance car c program digital tube display program)

MDK RTX51 开发51单片机，使用RTX，对于初始学者很方便(MDK RTX51 )

说明：  使用CC2530读取SHT20传感器的温湿度数据并发送或串口打印(This program get temperature and humidity data by SHT20 and send data though cc2530 with wireless or usart.)

基于单片机AVR-mega16的LCD12864（带字库）的驱动代码，可直接编译使用。(Driver code (with font) can be directly compiled based microcontroller AVR-mega16 of LCD12864.)

c8051f060定时器0，系统时钟，交叉开关IO配置(C8051F060 timer 0, the system clock, switch IO configuration)

说明：  步进电机的电子详细资料、对于了解步进电机3(For more information on the electronic stepper motor, stepper motor for about 3)

本文件是msp430单片机驱动液晶lcd1602的头文件(This document is the header file of LCD 1602 driven by MSp430 MCU.)

本程序实现如下功能：开机后，先初始化MPU6050等外设，然后利用DMP库，初始化MPU6050及使能DMP，最后，在死循环里面不停读取：温度传感器、加速度传感器、陀螺仪、DMP姿态解算后的欧拉角等数据，通过串口上报给上位机（温度不上报），利用上位机软件（ANO_Tech匿名四轴上位机_V2.6.exe），可以实时显示MPU6050的传感器状态曲线，并显示3D姿态，可以通过KEY0按键开启/关闭数据上传功能。同时，在LCD模块上面显示温度和欧拉角等信息。DS0来指示程序正在运行。(This program implements the following functions: boot, first initialize MPU6050 and other peripherals, and then use the DMP library initialization MPU6050 and enable DMP, finally, in an endless loop which constantly reads: temperature sensors, acceleration sensors, gyroscopes, DMP attitude Euler angles and other data solver after reporting to the host computer through the serial port (temperature does not report) using PC software (ANO_Tech anonymous axis PC _V2.6.exe), it can display MPU6050 sensor status in real-time curve, and displaying 3D gesture by KEY0 button on/off data uploading. Meanwhile, in the LCD display above the module temperature and other information Euler angles. DS0 to indicate that the program is running.)

单片机M8电子负载，包括原理图，源程序；可以参考学习一下(MCU M8 electronic load, including schematics, source code can refer to learn about)